Models > HSS25GFPJWW > Instructions

HSS25GFPJWW Hotpoint Refrigerator - Instructions

All installation instructions for HSS25GFPJWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HSS25GFPJWW
1,441-1,455 of 1,582
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

REFRIGERATOR AND FREEZER BLOWING WARM AIR

  • Customer: Robert A from Cambridge MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
PULLED OUT FREEZER SHELVES TOOK OFF BACK PANEL TOOK OUT OLD THERMOSTAT HOOKED UP NEW ONE PUT HEAT SHRINK TUBES ON WIRES TO KEEP OUT LIQUID, PUT BACK ON PANEL PUT IN SHELVES JOB DONE 10 MINS.CONDENSOR FAN PULLED OFF BOTTOM BACK PANEL TO EXPOSE MOTOR AFTER UNPLUGGING REFRIGERATOR TOOK 1/4 INCH NUT DRIVER TOOK WHOLE ASSEMBLY OUT TOOK OUT TOP SCREWS 2 THAT HOLD MOTOR TO BRACKET TOOK OFF BLADES CHANGED MOTOR PUT BLADES BACK ON PLUGGED IN FRIDGE PUT BACK PANEL ON JOB DONE 15 MINS.FRIDGE WORKS LIKE NEW AGAIN ROBERT SMITH JOB VERY EASY.

no ice being produced & on Hot point dbl sided frig panel between freezer & frig very warm

  • Customer: TIMOTHY from SPRING VALLEY CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Water still came out the front when pressed, but no ice. After removing the Ice container, & the top shelf I noted the icemake inlet was iced over. I turned off the icemaker, turned down the freezer temp, & allowed Ice to melt, but problem returned. I next removed the back bottom cover & cleaned the condenser coils, & drain pan; they were extremely dirty. Then I noticed the condensor fan was not on. After getting the nomenclature plate info off the condenser fan motor I left the back cover off, & put an external fan to blow on the coils as a temporaty fix until I could get the part & replace it. During that time the refrig functioned normally. 3 days later my condenser fan motor I ordered from Parts Select arrived & I installed it.

FAN SQEELS

  • Customer: richard from castle rock CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
REMOVE BACK PANEL . REMOVED FAN SHROUD. REPLACED FAN AND PANEL. OPS CK OK SO FAR

Fan and housing cannot be removed together.

  • Customer: Andenet from Haymarket VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy

refrigerator not cooling

  • Customer: Jeffrey from NEW YORK NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed cover above the light from the back of the freezer. I removed the fan and clipped the wire leads, after disconnecting the breaker to the fridge. I connected the wires with wire "union" from Radio Shack. Could have used wire nuts. I put the breaker on to check that it was running, then put the cover back on. However, to fix the build up of ice on the coils in the back of the freezer, I also replaced the thermisor and the heater coil after defrosting the coils with a hair dryer. Both were easy repairs and the fridge works fine.

Freezer not cold, Frig cold enough, runs all the time, Hot to touch in spots.

  • Customer: Kevin from York PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.

Ref. side warm, ice buildup in freezer

  • Customer: steve from palm city FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

freezer compartment icy;fresh food compartment warm

  • Customer: THONG from SPRINGFIELD VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

Side by side refrigerator side was not cooling, And freezer was not cold enough to keep ice from melting.

  • Customer: joe from cathedral city CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed back panel,removed ice maker.And you can see the two wires colors are a snap to identify cut the two wires spliced the new one in done deal!

Fridge warm inside

  • Customer: Grazyna from Oak Lawn IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My fridge starting getting warm inside so I took the back panel of the freezer off and seen the coils being completely frozen. I thawed it with hair dryer and took out both the heater element and thermostat off and performed an ohm test with multimeter. Heater seeme good with 23 ohm resistance but thermostat had no current flow through it. After replacing the thermostat the fridge works like new. I replaced the heater as well even though it seemed okay for peace of mind.

freezer was cold fridge wasn't

  • Customer: Chuck from Hebron NE
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Really easy unplugged unit took off back panel in the freezer thawed out coils remover sensor replaced with the new one put the unit back together works fine took about 35 min.

Running hot

  • Customer: Ken from Cloverdale IN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The mother board was bad....solder the board and it works like a charm.

refrig not turning off and defrosting

  • Customer: Robert from Orlando FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
replaced the defrost thermostat. The "how to" video was superb. Watched it twice before beginning the job. repair went as described.

Fridge warm, freezer side warm, ice buildup on back wall

  • Customer: edward from easton MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used your, diagnostic chart,whatched associated video and replaced thermostat. Easy , simple and cheap!!! I am thrilled with the website and service you provide. I definately will be back for more repairs as they arise. THANK YOU !!!!!

Refrigerator and freezer put out about 10 deg. F less than the electronic setting.

  • Customer: EDWARD from Beaumont CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Based on instruction I replaced the defrost thermostat and the temperature sensor. There was no improvement. The defrost thermostat was supplied with orange and red wires. the original wires were orange and pink. I connected the 2 orange wires and the pink to the red. So I don't really know if that is the problem or not. currently I don't know what to do next anyone got an ideas? It has dual evaporation.
All Instructions for the HSS25GFPJWW
1,441-1,455 of 1,582