Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HSS25GFPJWW > Instructions

HSS25GFPJWW Hotpoint Refrigerator - Instructions

All installation instructions for HSS25GFPJWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HSS25GFPJWW
1,171-1,185 of 1,609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leak

  • Customer: Frank from Lutz, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Had a water leak on that valve for probably the last 7 or 8 years. Only noticed it when I had a huge water issue with a leaky faucet. Repaired that, went to repair the Sheetrock behind refrigerator and saw water in the tray under frige. Wiggle hose and realized that the reason the water on the front door would only trickle out was because the leak on that valve was also affecting the pressure on the front door. Unreal!! The website and video made it incredibly simple to replace, u guys rock, for real!!!

No water to ice maker and water

  • Customer: Stephanie from Tishomingo, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch to step by step video instructions on your site. Great service! Part arrived the following day after order!

Water in Door would not cut off. Solinoid on flap ice shute would not close. Corroded and inoperable.

  • Customer: Kenneth from Blairsville, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video instructions were outstanding in showing how this repair was to be completed. Follow these instructions and Job was very easy. Replaced ice shute flapper and arm, soloinoid and Micro switch for water flow control. Reassemble by reversing procedure. Follow video instructions on how to replace water control valve in back of fridge. Test water flow at bottom front of fridge and defrost flow tube in door if necessary. I used tupperware container with hot water on top of ice shute shelf in fridge door. A couple of times changing and water was flowing. Great site and detailed video instructions for an effective and cost saving self repair. I saved several service trips and service calls and labor costs of a service tect. Parts costs were also a lot cheaper than service tech would have charged. Thanks PartSelect.

Ice not dropping in chute, frequent freezing up of dispenser.

  • Customer: Robert from Richmond Hill, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My GE Arctica refrigerator was constantly freezing up the chute that drops the ice. I googled the problem and found a youtube video on how to replace the solenoid and the dispenser door flapper. Repair was simple, removed the front panel with a small screwdriver, removed the circuit board and rear plastic assembly. Unscrewed the 2 screws holding the solenoid in place and snapped out the old flapper. Immediately I could tell the problem because the flapper was warped an not allowing a seal to form on the door. Youtube is great and I frequently go there to see if someone has made a video with the maintenance problems that I am having around the house. PartsSelect had my replacements here in one day. Saved a couple of hundred on a service call.

Flapper valve on icemaker wouldn't close anymore

  • Customer: james from ocran ridge, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched a video as prep. Popped plastic trim off(always scary, thinking plastic will break and it won't go back on), unscrewed control panel and popped wires off. replaced the items I had bought except micro switch which was fine. cleaned all the muck off the innards, replaced all plastic without anguish. I filled a glass with ice and watched with glee as the flapper slammed shut, keeping room air out and curing my iced up icemaker problem. God bless PartSelect!

flapper would stay open with cubes lodged in it

  • Customer: Joe from Harkers Is., NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used a putty knife to pry trim up around dispensing unit. Look up behind bottom edge of control panel for three small holes.(use flashlight) Used a small (1/8") phillips screwdriver to press up in holes to release panel. Remove flapper unit and selenoid. I changed black rubber flapper and solenoid. The solenoid is designed to hold the flapper unit open to allow all the cubes to clear the chute and it then is closed by the small spring after the delay. Works fine!

Ice door dispenser would not close on the freezer causing frost buildup on the inside and moster on the outside

  • Customer: Lee Ralph from Grenada, MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced ice dispenser solenoid which stuck due to the moisture causing it to rust I do recommend changing the rubber door flap also which allows the cold air to leak out therefore causing the solenoid to form rust

Ice maker door was not closing.

  • Customer: Idichandi from Coppell, TX
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Changed after watching U-Tube instructions. Faced trouble with the magnet assembly, had to redo it again, and it worked.

Solenoid and screws rust until the solenoid will not function and the assembly flapper will not close.

  • Customer: Roger from Hernando, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed all parts necessary, solenoid, recess retainer, dispencer door recess crank, and assembly flapper. Hardest part was getting old highly rusted screws out so I could remove the necessary parts. I replaced all screws with stainless steal screws, so the next time they will come out easier. This is the second time i've had to replace the solenoid because of rusty solenoid plunger, very poor design, not to mention the couple times i've taken the solenoid out to clean off the rust, but eventually its stops working because of the excessive rust on the plunger.

Dispensor Door not closing

  • Customer: Vic from Lake St Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video, repair was quick and easy. I replaced more parts than needed but I don't want to have to repair the door mechanism a second time.

cover would not come off

  • Customer: dan from Cape san blas, FL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the cover installed parts. Parts were very simple cover was a major problem. Instructions stated "simply remove cover by pushing on cover and clips will release" They dont and cover broke.

The solenoid was broken-water dispenser would not work

  • Customer: Dana from Torrance, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the dispenser panel and replaced-less than 10 min and a savings of $300.00 for a service call.

Ice was freezing at dispenser door and inside freezer

  • Customer: sanjay from trinity, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was amazing , i didn't know how to repair , i had. Insurance from choice home warranty but they say it is not covered , i was upset with them . But i get partselect .com . It is very easy, i tell my problem they tell what parts i need and also saw me video how to install it , i just did with a screw driver in 15 minutes . It was wonderful experience and a lot lot easy then what i thought. Thanks to partselect team and webside.

Ice Door Not Closing, building up ice in refrigerator

  • Customer: David from Oviedo, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power to unit. Using small Allen wrench unhooked 2 catches in electronic control panel. There are two holes underneath. Push up and pull out on panel as you release the catches. Remove wires. Remove 4 Phillips head screws in plastic panel, then remove panel. Solenoid has 3 screws. I replaced my screws being they were very rusty along with the solenoid. The spring on the door is easily replaced by removing two small screws on each side of the door hinge. There probably was nothing wrong with the old spring but for insurance replaced. Put the unit back together, no more ice buildup and clogging in ice chute through door. Likely saved $100 in labor repair bill by doing myself. Note: There is a few seconds time delay on the door closing. At first I thought I hadn't fixed the problem but then realized a delay in built into the system to avoid the door getting caught on any slow falling ice.

Shoot For Icemaker Would Freeze Up. Pieces Of Ice Would Get Stuck And Than Freeze Together.Dispenser Door Flapper Would Not Fully Close Anymore.

  • Customer: Karl from Miromar Lakes, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the vidio on your site, it was very helpful. Careful lifted the frame, unhooked the display panel. With phillip screwdriver took the 4 srews off, unhooked the pc board. Take out 2 srews for the doorflapper. Loosen top screw for soliniod, take out 2 bottom srews and take out soliniod. Clean up area with paper-towel. Replace all new parts. And it works great again.
All Instructions for the HSS25GFPJWW
1,171-1,185 of 1,609