Models > HSS25GFPJWW > Instructions

HSS25GFPJWW Hotpoint Refrigerator - Instructions

All installation instructions for HSS25GFPJWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HSS25GFPJWW
1,501-1,515 of 1,582
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Condensor Fan Motor not working, unit getting hot

  • Customer: Ron from Metairie LA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Noticed the interior wall hot to the touch when opening cooler or freezer door (side by side). pulled lower panel off in rear of unit and noticed fan motor not working. Ordered new fan motor, installed , still did not work. used volt meter to test for power from main control panel to motor. No power present. Ordered main control panel board and installed. Fixed problem. It ran excellant for about an hour and then the control panel shorted out the main control panel and motor that had just been purchased. Both were replaced at no additional charge by Customer Service. Second installation was a success. Sometimes bad things happen to an already bad situation. It's nice to have the understanding, support and service offered by Parts Select. I guess that's why I use them every time there is a problem. G E is easy to repair as long as you use patience and determination.

The water and ice dispenser suddenly stopped working. The light in the dispenser would dim whenever we tried to get water or ice.

  • Customer: BILL from N OLMSTED OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the power cord, removed the screws and the cover. After removing the screws from the main control board I unplugged all of the connections from the bad board and plugged them into the new board in the same order. An easy change and a real moneysaver!

Freeze and refrigerator sides at times were warmer than normal. Would not dispense water or ice threw door dispenser, also could hear a clicking noise every so often the last about 10 minutes at a time. I think the clicking would start on the main board when it went into the defrost mode. Defrost mo

  • Customer: Winston from Ford VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
UNPLUGGED the Refrigerator.Removed two screw from the panel on the (outside) back, took panel off, removed the wire harnesses, carefully removed old board off of the plastic pins, pushed new board on the pins, put wire harnessed back on in their proper places, put cover back on. Everything that was not working, was working now. Took less than 15 mins..

Circmit Board for the Refrigator

  • Customer: John from Anaheim CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Read instructions,unplugged refrigator from wall socket, removed screws,remove cover, unplugged cables, removed old board, placed in new board, connected cables, put on cover,replaced screws,,,,plugged refrigator into wall socket. so far all is well.

My refrigerator suddenly stopped dispensing ice and water

  • Customer: Timothy from Birmingham AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I did an internet search on the issue, which was that my refrigerator suddenly stopped dispensing ice and water through the door. Also, the refrigerator had been cycling on and off constantly for some time. I found a YouTube video showing how to replace the main control board; along with a link to order the new part. I ordered the part and selected standard shipping. My part arrived in 48 hours. I replaced the main control board just like in the video. My refrigerator works like new now. I was able to solve my problem in two days on my own, for the cost of parts only. I am sold on PartSelect.com.

Warm temp After a power outage

  • Customer: TIM from FT. WAYNE IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Should have had an idea that it froze up When use of a generator on/ off use for five days And dirty condenser Their should have been a trouble shooting examples

ice maker fail, water dispenser fail, progressively worse

  • Customer: douglas from englewood CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Unplug, replace board, plug in, everything working.

Freezer too warm

  • Customer: Antoinetta from Lake Ronkonkoma NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The video instructions were easy to follow as well as the replacement. The replacement Main Control Board is generic to different refrigerators and has more connectors than the original. Be sure to identify the locations prior to removal and installation.

unthawed twice then third time compressor wouldn't start up but cooling fan would still run

  • Customer: Donna from Charlotte MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled cover off back that housed the board. Unplugged all the wires that went to the board. wires will only fit in one spot so you cannot mess it up. snapped it off the pegs, then replaced new board in same spot. hooked plugs back up and installed ground wire. covered it back up plugged it in and it ran.

I replaced what I thought was a faulty mother board. It was easy to do.

  • Customer: Rolland from Derby NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replacing the motherboard was really easy. However it has not fixed my refrigerator. I continue to have cooling issues with fridge and sometimes with the freezer.

Fridge and freezer consistently get warm during Summer

  • Customer: Robert from Bearsville NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After pulling fridge out from the wall, removing the bottom back panel and inspecting the fridge operating parts, I noticed the condenser fan never comes on. Reading online I found that most of the time the problem is with the main control board. I simply unscrewed the back panel, carefully disconnected the cables from the old board, plugged them back in to the new board, replaced the panel and started the Fridge back up. It cooled right down to normal temperature within the hour! Five years of neurotic behavior around cooling the fridge were over! My wife and I constantly rearranged various fans around the kitchen and joining rooms, opened the cabinet above, taking out the bottom shelf to make more ventilation, pulling the fridge out from the wall several inches, and worrying every time the freezer went up to 9 or 10 or even 20 degrees, and the fridge section up to 40 or even 45 degrees F. I can sleep easy now, and use the fans on us in hot weather, rather than the constant buzz in the kitchen. We can even have a conversation without yelling above the din of the fans!

the brain died

  • Customer: Anthony from Brooklyn NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
it was very simple to replace 3screws to remove cover 1 screw to disconnect ground 4 prongs squeezed to remove board and then disconnect the plugs and thats it thank u again

Water dispenser quit working.

  • Customer: Ralph from Spring Valley CA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Defrosted the fridge.

compressor was'nt running

  • Customer: Paul from Coventry RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
very well, replaced min board in less than half hr.

Refrigerator not cooling either freezer or refrigerator sides

  • Customer: JAMES from JEFFERSON MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Found refrig. not working properly. removed back cover to access compressor and condenser fan motor. Fan motor turning very slowly if at all. Compressor tripping thermal overload. Blew out condenser coil of all dust. Figured it was either a circuit board or cond. fan motor. Went online to Parts Direct and read through other blogs of issues with this appliance. I ordered both the fan motor and circuit board. Replaced circuit board first. started it up and fan ran great. Compressor however kept tripping overload. All that overheating stressed that start relay so I disassembled and removed relay and thermal overload. Sure enough, relay was all broken up inside. I put a 3 in 1 hard start kit on it from a local supply house and it now runs great. I will order the new o/l and relay so I can remove hard start kit.
All Instructions for the HSS25GFPJWW
1,501-1,515 of 1,582