Models > HSM25GFRASA > Instructions

HSM25GFRASA Hotpoint Refrigerator - Instructions

All installation instructions for HSM25GFRASA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HSM25GFRASA
1,456-1,470 of 1,593
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice dispenser door not closing after used

  • Customer: nelson from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
with a Philip screw driver push up the control module which have three holes by the push dispenser...changed the spring,dispenser door assembly/flapper,solenoid and recess crank.after putting everything back together dispenser works fine..

Faulty solenoid and flapper assy

  • Customer: Blanhue from Bruceville TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I simply followed the video instructions and it was a breeze, so easy I couldn't believe it . The GE repairman where going to charge me approx. $265. 00 for this repair and another service person wanted to charge me $ 100.00 just to remove and replace these items that I purchased from you . The experience was great as well as the SAVINGS, Thanks again for your professional service. Also I did receive a defective part and this company sent this part back to me within 2 days , preventing any delays on the repair. Thanks, Blanhue

problem with dispensing ice from door

  • Customer: Bertha from Dugger IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video, did exactly as it showed.

ice flapper would not close

  • Customer: Louis from sloansville NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The first thing I did before starting the repair was watch the 2 videos. I followed the directions step by step and within an hour I had a functioning ice maker again. I had searched all over the web and the other sites were of no help. Your site really made it easy to figure out the problem and order the right parts. I now have a problem with my dishwasher so I will be back on your site soon. Thanks!

Freezer kept "icing up" because flapper door would not close.

  • Customer: Anthony from Mount Vernon IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Video and instructions were very thorough, but on my paticular freezer, the inside door shelves had to be removed (30 screws) to get to the face place to release the door controls. Newer models can be accessed from the front. After removing front cover, repairs were very simple. Found that the solenoid was "rusted" and would not function. Easy replacement. Order new flapper, but was not needed (have a spare now...haha). When putting back together, the door did not seal at top...had to adjust how I tightened screws (pattern - top to bottom) to keep door from "warping". Did not think that the small amount of torque on the screws could "warp" a door so easily. After re-torqueing the screws, moved the top hinge just a little and door again sealed correctly. Will keep this site "bookmarked" for all my future appliance needs. Never had customer service so thorough. Amazing that I order about 5:00 pm on a Thursday and parts were at my door just after lunch on Friday...amazing service. Thanks for the instructions, video and CS.

The Ice ejector flap was hanging

  • Customer: Frank from Tallahassee FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The ice maker was frosting up and the flap was sticking open. Only one negative comment! The Parts Diagram did not show how to remove the exterior trim plate to get to the parts. Once I figured that out, it was an easy installation and the ice maker ejects the ice properly and the flap closes properly. I could do the install in 20 minutes next time. Thanks for your help. Frank

Ice was freezing in clumps in the shute(in door itself) and prohibiting the flapper from closing. Warm air enters from the kitchen through this opening and melts/freezes the cubes in shute into a clump.

  • Customer: Salvatore from Fort Myers FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1-Duct taped around the rectangular grid on the face of the door.2-Usinng a putty knife I removed the frame(just held with small plastic grommits3-The front panel with buttons for water/ice etc---push up and remove.4-Did not unplug the refrigerator until after this item was lifted up and I duct taped it to the refrigerator door to keep it out of the way.5-Once taped out of the way I unplugged from electrical.(***there was no need to unclip the small connectors to this panel----less likely to break the prongs if the above is followed)6-2-3 screws removed the solenoid which in my case was my problem(((Solenoid was completely destroyed by the amount of rust that it exhibited. ******If you have to replace flapper and or it and the spring-----this doesn't look very difficult either. Just keep the doors shut while electric out. I'm handy but not an expert on anything---doing it was easier than what I expected. Should take no more than 1-2 hours

Ice dispenser door not closing. Two possible fixes

  • Customer: John from Newnan GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the videos for replacing both the solenoid and the ice door flapper. Ordered the parts, watched the videos again and changed out the parts. I used a Philips head screwdriver and a little WD40 to clean up some rust. The instructions in the video were very easy to follow and simplified the process. PartsSelect's video showed the demonstration on a refer like mine as opposed to another site, which helped me be familiar whenI opened it up.

ice flapper would not close

  • Customer: David from north port FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front display and solenoid 3 screws and replace. Clean and install

Ice dispenser flap stopped opening and caused water dispenser line to freeze

  • Customer: ADAM from ORANGE BEACH AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pull fridge away from wall and unplug it! Turn water valve off. Open freezer door and stuff a small rag/washcloth in hole where ice exits to keep the cold air in. There are 3 small holes on the bottom of the control panel, stick a small Phillips head screwdriver in the 2 outside holes and pop the control panel out. Pull the 3 connectors out of the back of the control panel. Set the control panel aside. Unscrew 4 Phillips head screws holding the plastic control panel bracket/ice cup/light bulb. Set this piece aside. Unscrew 3 screws that hold solenoid. Mine was completely rusted. Throw the old solenoid in the garbage. All the screws I removed were rusted. Go to home depot get some stainless steel screws that are the same size as the rusted screws and some spray rust inhibitor for metal and a tube of anti-seize. Wipe everything down with 1/10 solution of Clorox/water(q-tips help to get the tight areas)to get rid of all the MOLD. Spray a light coat of rust inhibitor on your new solenoid and let it dry. Coat the metal plunger of your new solenoid with anti- seize lubricant. Replace solenoid and all other screws that are rusted with stainless steel screws. Put the plastic bracket back in with 4 screws. Plug the 3 control panel wires back in and pop the control panel in the bracket. Pull the rag out of the ice chute, turn water back on, plug fridge in and push it back against the wall. Your done and hopefully the extra steps will help your solenoid last longer! Hope this helps!

Flap not closing completely causing ice build up in freezer

  • Customer: Victor from Aylett VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Slip the front cover off by gently pulling down, carefully un-plug the wire connectors (x3), remove 4 screws and remove paddle assembly. 2 screws hold the flap on and 3 hold the solenoid. Replace the screws with stainless so they won't rust. I tried coating the solenoid in lithum grease to prevent rust, onlt time will tell if it works.

Some screws was rusted so I take more time.

  • Customer: huan from garden grove CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I just follow to the video and take step by step. It's was very helpful and easy. Thank you.

Ice dispenser flap door stayed open

  • Customer: Douglas from Hickory Corners MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the Control Panel and the outside of the Dispenser Outlet. Removed the Flapper Door and the solenoid. Replaced both parts with new parts, and re-assembled. The pin, at the top of the Solenoid was badly worn and the plastic arm was very rough on the surface adjacent to the worn pin.

Bad solenoid - ice flap didn't close

  • Customer: Wesley from Champaign IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The video was clear and the repair looked easy. My only problem was that the trim piece that had to be removed first was very hard to get off. I called PartSelect and ask if I was doing it correctly. (I didn't want to damage anything else) The person I talked to said that they don't provide technical service help but that he'd look at the diagram of the refrigerator to see if he could help me. He was able to confirm that I just had to apply more force to get it off. With the aid of a putty knife I was able to pry it off. After that I followed the video instructions and it was easy to make the repair. Things went back together easily and the problem was resolved.

Ice tunnel distorted by hair dryer. Flapper leaking air. Solenoid not activating

  • Customer: Donald E. from Mt. Washington KY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed snape on trim with flat knife and some efford. Removed control as Steve instructed. Removed 4 screws from tunnel assembly. Unsnapped old tunnel and snapped in new. Exchanged flapper as Steve instructed, no problem. Removed 3 screws from seloniod assembly. Remove and replace with new. Replace control and wires. Replace snapon cover. Turn water on and plug in freg.
All Instructions for the HSM25GFRASA
1,456-1,470 of 1,593