Models > HSM25GFRASA > Instructions

HSM25GFRASA Hotpoint Refrigerator - Instructions

All installation instructions for HSM25GFRASA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HSM25GFRASA
1,171-1,185 of 1,593
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ICE AUGER BROKE IN IN ICE BIN

  • Customer: RONALDO from CONWAY SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I USED THE ON LINE REPAIR VIDEO AND EXCEPT FOR OVER LOOKING ONE OF THE PROCEDURES ON PUTIING THE PARTS BACK TOGETHER IN ORDER. THE REPAIR WAS RELATIVELY EASY FOR ONE WHO HAD NEVER ATTEMPTED SUCH AN REPAIR. I HAVE VIEWED SEVERAL ADDITIONAL REPAIR VIDEOS OF YOUR COMPANY AND FEEL CONFIDENT THAT OF THOSE VIEWED I COULD EASILY REPAIR MY REFRIGERATOR'S PARTS THAT MAY QUIT WORKING. PLEASE CONTINUE TO POST THESE EASY TO FOLLOW INSTRUCTIONS?

Auger blades had broken off

  • Customer: DARLENE*WHITE from CROSS SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replace old auger with new one.

Broken auger, plastic in ice bucket

  • Customer: Craig from Katy TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Simple easy to follow instruction, very easy removal and installation. But for someone without mechanical skill, I dont see it being as easy as it was for me.

The Auger had broken in the ice maker so ice would not dispense

  • Customer: Brian from Albuquerque NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the part and was sent a link to a video that did a great step by step visual of the repair. I had my laptop and played the video ( paused a few times to catch up) and had the repair done within an about 30-45 minutes. The video covered everything that needed to be done it was great.

Broken auger wouldn't dispense ice

  • Customer: jason from Tuttle OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
ordered part- arrived in about 4 business days & along with email from partselect detailing replacement I completed in about 20 minutes. I'm completely impressed with partselect and will take on next repair big or small using this service! Thanks for such a simple process, start to finish!

Auger Disp

  • Customer: Bryan from Sugar Land TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
After watching the video it was easy. Took less than 10 minutes to replace. PartSelect really does it right with the consumer.

The auger in my ice bucket was broken

  • Customer: Mary from Florissant MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the repair video and followed along pausing the video as needed to complete the steps. I'm not sure I could have done it without the video. That was wonderful. I will definitely order any parts I may need for other appliance repairs from Parts Select and utilize the amazing repair videos.

Broken auger blades

  • Customer: Charles from Baton Rouge LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Although there were many steps to the repair process it was relatively simple due to the excellent on line video. A link to the video was provided with the shipping confirmation. Thanks

ICE MAKER AUGER BROKE

  • Customer: GREGORY from Shawano WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1st. I watched the video on the web site. "BIG HELP".It walked me thru the repair and all went fine. Ice maker works great. Thanks

The last coil on the end of my auger had broke off and the ice tray would not feed ice out of the box.

  • Customer: Timothy from Douglas AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The ice maker tray was removed and the e-clip was removed from the end of the auger shaft,I then released the snap clip retainers and removed al the screws to romove the end of the Ice crusher section on the box.(It is a good idea to run this whole unit under hot water as the plastic could crack if to much force is applied during dissasembly. Plastic can be brittle when very cold). The shaft (auger)was extracted and the plastic retainer nut removed with a channel lock plier. Careful as it has a left hand thread. I was then able to remove the crusher blades and bushings from the end of the auger shaft and reassembled the parts on the new shaft. Refer to the parts catolog blowup view page on the website for proper installation of these parts if you get them mixed up. It is of great help. I then reassembled the auger back into the box and reassembled the other parts and screws to finish assembly. Popped it back into the frezzer and it works perfect. Tools required were nothing more than a thick kitchen towel to hold the Auger down and a flathead screwdriver for the e-clip retainer. A channel lock plier to take of the end nut as it has no flats for a wrench and a phillips screw driver for a couple of screws. Total time was about 20 minutes. I probably saved about $100.00 in doing this myself. Thanks again to PartSelect for getting my paet to me in a couple days.

AUGER IN ICE BUCKET BROKE

  • Customer: TERRY from BIRMINGHAM AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
REPAIR IS FAIRLY SIMPLE YOU DO NEED TO KNOW THAT NUT AT END OF AUGER IS LEFT HAND THREAD AND ICE CRUSHER ASSEMBLY ONLY GOES TOGETHER ONE WAY. SO PAY ATTENTION SURING DISASSEMBLY

auger in ice tray broken

  • Customer: Henry from Fort Dodge IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the auger

Ice Maker not making ice

  • Customer: George from Katy TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

ice maker was leaking water. Cubes were sticking inside tray.

  • Customer: Carl from Abilene TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

Ice Maker stopped working

  • Customer: William from San Tan Valley AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.
All Instructions for the HSM25GFRASA
1,171-1,185 of 1,593