Models
>
HLPW028AXW
HLPW028AXW Haier Washer - Overview
Sections of the HLPW028AXW
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
WASHING MACHINE WATER INLET VALVE
PartSelect #: PS12343364
Manufacturer #: WH13X26636
$37.50
In Stock
WASHING MACHINE ACTUATOR MOTOR BRAKE
PartSelect #: PS12343434
Manufacturer #: WH20X27368
$41.09
Special Order
WASHING MACHINE CONTROL PANEL SEAT
PartSelect #: PS12343489
Manufacturer #: WH44X26195
$49.49
In Stock
Questions And Answers for HLPW028AXW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cynthia
November 12, 2019
Why is my washer HLPW028AXW shutting off the electrical breaker when it gets to the spin cycle
For model number HLPW028AXW
Hello Cynthia and thanks for writing.
When an RCD circuit breaker trips or a fuse blows when your appliance is in a spin this is usually caused by leakage to the ground or a short-circuit. The problem can be caused by incorrect connection of the appliance. Make sure your unit is not leaking water during the spin circle. This could also be caused by a worn belt # PS4126140as it would overheat so check this part as well.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the HLPW028AXW
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The water stopped draining.
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho ... Read more tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho ... Read more tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Read less
Parts Used:
-
ILANA from NEW YORK, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't drain.
Lifted up the washer from the bottom. Accessed the pump, unscrewed the motor and pulled off the rubber hose attached to the pump using a Phillips screwdriver and a wrench.
Reattached the hose and the mounting screws. Worked just fine.
Reattached the hose and the mounting screws. Worked just fine.
Parts Used:
-
GABRIEL from GANADO, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench (Adjustable)
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace inlet valve
Easy. Just need to remove top and 1 panel to access. Not too tight of a workspace.
Parts Used:
-
Annette from SEATTLE, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!