Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HLD4040M15SA > Instructions

HLD4040M15SA Hotpoint Dishwasher - Instructions

All installation instructions for HLD4040M15SA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HLD4040M15SA
76-90 of 268
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Middle Arm Spray Hub

  • Customer: Dan from Purcellville, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 5 people found this instruction helpful
Due to loading a tall item in the lower rack of the dishwasher. The constant hitting of the spray hub, the hub broke.

I purchased the Middle Spray Arm Hub and using a hand nut driver, I unscrewed the nut and attached the new Hub and screwed it back in place.

The replacement was very easy and the cost of the part was very reasonable.

Delivery was quick and the dishwasher was up in running 10 minutes after the part arrived.

I would use this company again and I give them an A+ rating.

Dan Dailey

Leak under the appliance

  • Customer: paul from arlington, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 3 of 5 people found this instruction helpful
After finding the leak source I have targeted the piece part on your web. It came 2 days after and I replaced the defective part by the new one. I switch off the water, untied the nut to release the pipe, take out the part.

Front door on Dishwasher Leaking

  • Customer: Rick from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!

Door latch broke

  • Customer: Joe from Clinton township, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
took off eight philips screws on inside door panel which then exposed the broken actuator and missing spring. Replaced broken and lost parts and reset actuator in door then reinstalled inside door panel. Done and I'm happy not to have called service.
Joe

First silverware basket had a hole in it.

  • Customer: Jackie from Lebanon, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Took out old one and put in the new one. Not hard at all. Thanks

Lower spray arm falling apart, dishes not cleaned

  • Customer: David from Lincoln University, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 6 people found this instruction helpful
This was very easy. 1) roll out lower rack, 2) rotate lower arm slightly counter-clockwise and lift it out, 3) install new lower arm by dropping into position and rotating clockwise. 4) roll in lower rack, and roll out upper rack, 5) use a nut driver to remove the retaining bolt/screw from the upper arm - it's in the center of the upper arm and you have to work from underside of upper rack, 6) remover upper arm, 7) install new upper arm by holding in position and re-inserting the retaining bolt/screw. 8) Tighten the retaining screw and make sure upper arm freely rotates.

The water valve went out

  • Customer: Paul from Terra Ceia, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench set
  • 2 of 4 people found this instruction helpful
I took the old one off and replaced it with the new one, which fir perfectly.

Old soap dispensor latch would not hold

  • Customer: Kenneth from Dublin, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 4 people found this instruction helpful
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

The upper try roller was broken

  • Customer: Howard from Mount Prospect, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Unscrewed the old roller. But it was difficult to replace the roller as the rim of the roller would not fit into the slide mechanism and allow the screw to engage the hole. What I thought would be a 2 minute job turned out to be more like 20 minutes. I suspect there is a way to release the slide stop so that the top basket could be removed with its slide bar, but I did not see how to do that. I finally was able to "force" the screw into the hole

Broken middle spray arm

  • Customer: Pamela from Bakersfield, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 1 of 1 people found this instruction helpful
Unscrewed the screw holding it in place and removed it, out the new one in place and screwed it on. Very quick and simple.

Plastic part of inlet valve cracked

  • Customer: Barbara from Georgetown, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 2 of 4 people found this instruction helpful
Hired my neighbor, who is a plumber.

The wheels on the upper basket had broken

  • Customer: LELAH from LANSING, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
I removed the plastic end caps by gently pushing and twisting them. Once the end caps were off the basket slid out. The old wheels were removed and the new ones clipped in very easily. I then slid the basket back into place and replaced the end caps. The most difficult part was removing the end caps. I was afraid that I would break them, but by being careful and not forcing the piece they easily came off.

wouldn't drain

  • Customer: JOHN D. from GOSHEN, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 3 of 7 people found this instruction helpful
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.

PS259168 Replaced broken end cap on upper dish rack

  • Customer: Stephen from Waterville, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

New install missing drain tube and clamp.

  • Customer: David from Norwell, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 2 of 4 people found this instruction helpful
Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.
All Instructions for the HLD4040M15SA
76-90 of 268