Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HDM1853WJ05

HDM1853WJ05 General Electric Microwave - Overview

Get Parts and Repair Help for HDM1853WJ05

If you know the microwave repair part you need, you can browse the list of all parts on the HDM1853WJ05, or you can search by name or part description. You can also find your part by where it is located on the HDM1853WJ05 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. We’ve also included any installation videos we have for HDM1853WJ05 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the HDM1853WJ05

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.19

Halogen Light Bulb - 120V 20W

This lightbulb is located on the inside of your microwave. The bulb is behind the top grill. It will need to be replaced when it has burnt out and no longer works. Unplug the unit....

Order within the next 41 mins and your part ships today!
$6.98

Light Bulb - 40W 130V

This light bulb is a 40 watt, 130-volt clear appliance light bulb that is manufactured to fit microwaves with small-base light bulb sockets. The light bulb illuminates the inside of the microwave while the microwave is running. You may need to replace this part if the existing one is burnt-out or broken. If the existing light bulb is broken, disconnect power to microwave and remove the bulb base with a pair of needle nose pliers. This is a common wear item, so it is recommended to order a spare. These light bulbs are sold individually.

Order within the next 41 mins and your part ships today!
$7.63

Line Fuse

This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the to...

Order within the next 41 mins and your part ships today!
$13.05

Light Socket - 250V 75W

This is a light bulb socket that is manufactured to fit a microwave appliance. The socket is meant to fit small-base light bulbs. The light bulb is not included with this part, so consider ordering the light bulb if necessary. You may need to replace this part if the existing socket is broken, cracked, or if light bulb is not turning on, and a new light bulb does not work. This is an electrical part so please be sure to disconnect power to your appliance before repair.

Order within the next 41 mins and your part ships today!
$21.50

Secondary Door Switch

The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open. The switch monitors the door latch position, and communicates ...

Order within the next 41 mins and your part ships today!
$10.61

Glass Light Lens

The microwave glass light lens protects the light bulb inside the appliance. It is clear in color and measures approximately 6-1/2 inches long, and 2-1/2 inches wide. You may notice that this part is cracked or broken and will need to be replaced. You will need to remove the screw holding the cover in place. Unhook the cover from the bottom panel. Bend the tabs up that are securing the old lens in place. The textured side should be facing up. Place the new lens into place and secure back into place.

Order within the next 41 mins and your part ships today!
$66.80

Glass Cooking Tray

This tray rotates in your microwave ensuring more even temperatures and is approx.14-1/2 inches in diameter.

Order within the next 41 mins and your part ships today!
$9.74

Glass Turntable Coupler

This part accepts a D-shaped motor shaft.

Order within the next 41 mins and your part ships today!
$48.86

Drive Motor

This is a microwave turntable drive motor. This is a genuine OEM replacement part. It accepts a D-shaped drive shaft. The drive motor is located under the glass microwave turntable...

Order within the next 41 mins and your part ships today!
$19.78

Monitor Door Switch

Unplug your microwave before attempting this repair. You will need to remove the grill, which is held into place by two screws at the top of the grill (open your microwave door before doing this). Remove the grill. Remove the screw on the left holding the control panel in place. Loosen the screw behind the panel. You should now be able to lift the panel up and pull forward to detach. You will find the door switch by removing the screws to detach the switch assembly. Press on the release tab to remove the middle switch. Disconnect the wire connector to release the old switch.

Order within the next 41 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave completely stopped working

  • Customer: Kim from Cliffside Park, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 708 of 929 people found this instruction helpful
Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove an... read more

light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up

  • Customer: Marla from Arlington, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 217 of 247 people found this instruction helpful
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the ... read more

Lens cracked and bulbs burned out

  • Customer: Mark from GRAND BLANC, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 200 of 273 people found this instruction helpful
First I removed the single screw holding the lens assembly in place. Then I lowered the assembly and tilted it until it came out. To remove the existing cracked glass lens there were four tabs bent down on it. By hand I lifted each tab just enough to remove the broken lens. I then replaced the broken lens with the new one and re-bent the tabs down by han... read more