Models > HDA3700G00WW > Instructions

HDA3700G00WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3700G00WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3700G00WW
691-705 of 729
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

rollers broke

  • Customer: James from Simpsonville SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed new ones as per instruction

Dishwasher was leaking out the left front

  • Customer: Anita from Boon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the corner baffles and installed them in the corners in just minutes. Repair company quoted me about $100 if they had the parts on the truck. If they had to come back it would be another service call. Did the repairs my self for $24 with shipping charges. Happy Customer

did not pump out all the water before drying

  • Customer: james from ham lake MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
looked up the model no. on partselect web site and they discribed several diagnoses for different problems.they gave a 19% probability for a bad valve and nut. i removed the cover and the nut valve and the valve looked pretty bad. i ordered a new part and delivery was very good.i replaced the part and that took care of my problem. i was very happy with the whole repair.

roller broke

  • Customer: Sam from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
follow your video instruction. very simple.

The dishwasher was not draining

  • Customer: Marcus from Argyle TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The machine had been running sluggish for a while. Replaced the pump awhile back, but it still wasn't draining good. Then it quit draining. The solenoid is mounted on the pump, two screws and a clip on the valve door shaft come off. The new one is easy to put on. Caution: many of these appliance people say that timers are often needlessly replaced, but when I looked at the old solenoid, it looked like a meltdown had occurred. It was not worn out, it had overheated. Checked out timer and found cause. The gear on the motor shaft was partially stripped, causing drain valve to stay open too long. New timer, solenoid, pump-ten years old and never ran this good.

Broken clips

  • Customer: Michael from Novi MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Clipped in new wheels and clips

Rear wheels would not clip to the dish rack due to usage and age.

  • Customer: Bernard from South River NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Place the axle inside the wheel. Mount the wheel to the bottom of the dish rack and snap the axle to secure the wheel to the dish rack. Total project time less than 5 min. Video to replace wheel and axle was very helpful for those who are not mechanically inclined.

Hing arm broke

  • Customer: Peter from Davenport FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Water leaking on floor from valve base where it mounts to bracket.

  • Customer: Ronald from Charleston SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Turned off power and water to dishwasher, removed kick plate to dishwasher, removed mounting bracket from frame rail of dishwasher, unplugged valve then used pliers to remove spring clamp on rubber line and used box wrench to remove water line attached to brass connection. There was a lot of calcium build up around screen and rubber O-ring and cleaning that may have fixed it but pulled off anyhow. One problem I had is that the old part would not come apart where the L-joint screwed into the collar that attaches to valve on old setup to allow new one to be bolted to it. So I looked at putting new valve on the old mounting bracket. That did not work after I got it apart as the new bracket is flat while the old is counter sunk...and the new valve has a larger footprint and would not fit flush to seal. So back to work bench and put valve in vise as the threads had plumbers pipe cement it looked like and they were tight. Got the two joints apart...cleaned with wire brush...sanded down mouth of brass collar that fits against O-Ring of new valve to make sure clean. Put teflon tape on all threads and tightened it all back up. Reconnected, plugged in, mounted to dishwasher and ran a full cycle with dishwasher pulled out so I could monitor any leakage from beginning. All is good...so slid back under sink and ran load with dishes...noticed water on floor. Freaked out...pulled it all out and valve was dry. I forgot to clean up the little bit of water that came out of lines when disconnected first time for repair... :) All is good now.

dishwasher would not fill with water

  • Customer: peggy from moreno valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Researched problems on internet,based on info ordered part. Got it in 24 hrs.followed package directions. So easy and for less than a service call! Runs like a charm now.

No water fill to dishwasher.

  • Customer: Lewellyn from Clarkston WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced the water-fill solenoid valve.

Water leaking under dishwasher.

  • Customer: Louis from Dover DE
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I first shut off the power to dishwasher, then shut off water and disconnected the water supply line. Then pulled the washer out from under counter and layed it face down. Undid the hose clamp from sump housing and clamp for wash arm rubber connector. Disconnected screw for the motor brace. Motor swung out of way. Pulled out sump housing and cleaned the edges of the hole. Pushed housing threw bottom and got it to seat in the groove inside the washer. I then unscrewed the rubber for the wash arm and cleaned those areas too. Screwed the new connector on and made it tight, old one was loose. Moved the motor back and reconnected hose clamps and reattached the motor support bracket. Stood washer back up and pushed it back under the counter. Reconnect water line and turned water back on to make sure it was not leaking. Turned power back on to washer. Then poured a large pot of water into washer and turned on and kept checking for leaks but there were none. Finished putting cover plates back on and the washer was done. Then I had to replaced some of the flooring that was damaged from the leaking of these two parts.

Pump was leaking from the shaft seal

  • Customer: Anthony from Mechanicville NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.

dishwasher does not drain

  • Customer: tom from bend OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working

Rubber piston on check valve was almost completely gone. Water backed up finally to the point of overflowing on kitchen floor.

  • Customer: Ken from Central Square NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Simply followed the instructions for the part on the part page. One thing that helped taking out some screws was to remove a couple of the brackets that hold the heating element and move it slightly. I would suggest cleaning all of the gunk out of drains and clean all holes in the screens using a toothpick, etc. Be careful not to overtighten the nut for the next time you have to do this!
All Instructions for the HDA3700G00WW
691-705 of 729