Models > HDA3500N10WW > Instructions

HDA3500N10WW Hotpoint Dishwasher - Instructions

All Instructions for the HDA3500N10WW
481 - 495 of 530
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Roller wheels in upper rack wore out
The switch out was quick and super easy. I had the top rack off, wheels changed out and rack back in in ten minutes
Parts Used:
Upper Roller and Axle - Kit of 4
  • Bill from Seattle, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water leak on the bottom right side of the door
replaced the rubber baffle
Parts Used:
Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right
  • Daniel from Oakland Gardens, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
one roller was broken
replaced all four rollers
Parts Used:
Upper Roller and Axle - Kit of 4
  • Fred from Pueblo West, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Parts Used:
Rinse Aid Fill Cap
  • John from Corvallis, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
top rack falling
watched video on website - very easy repair
Parts Used:
Upper Roller and Axle - Kit of 4 RACK SLIDE END CAP
  • Bernadette from Contreras, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not start
Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.
Parts Used:
Interlock Switch
  • Howard A. from Little Elm, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
not draning
Removed bottom panel unplugged wires removed two screws removed it then replaced it
Parts Used:
Drain Solenoid and Bracket Assembly
  • William F from new castle, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
upper dishrack needed replacement
In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.
Parts Used:
UPPER DISHRACK
  • Gerald from Wichita, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Faulty Dishwasher Door Latch
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.
Parts Used:
Door Latch Kit
  • cliff from knoxville, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Parts Used:
Interlock Switch
  • Robert from Riverview, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would Not Start
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.
Parts Used:
Interlock Switch
  • JoAnn from Daytona Beach, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
all the tines had lost their coating and was starting to rust
bottom rack was easy. on the top rack, I used as quarter to release the plastic ends on the two sliders. Google had video showing how to do this using a quarter.
Parts Used:
UPPER DISHRACK LOWER RACK
  • David from Elkridge, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken rollers
within 5 minutes.Great site for information and parts
Parts Used:
Upper Roller and Axle - Kit of 4
  • Bruce from Souderton, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
installing new wheels on upper rack of dishwasher
I thought to myself, this is going to be easy, but I hit a couple bumps getting the end caps off. I just watched the video and it was great and helped me be sucessful. The only thing that would have helped was instructions on how to put the end caps back on! david
Parts Used:
Upper Roller and Axle - Kit of 4
  • David M from Bonita Springs, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
The axle rusted through on top tray of tray
Removed the tray from its rails. Removed axle clips fro tray and replaced with new axles. Put tray back in rails and I was done. Works like
Parts Used:
Upper Roller and Axle - Kit of 4
  • william from Canal Winchester, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HDA3500N10WW
481 - 495 of 530
Back to Top