Models > HDA3500N10BB > Instructions

HDA3500N10BB Hotpoint Dishwasher - Instructions

All installation instructions for HDA3500N10BB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3500N10BB
76-90 of 510
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Part of a roller on the upper rack had broken

  • Customer: Janice from Murphysboro IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I removed screws holding the rollers to the side of the dishwasher. I pried the end caps from the slide. I removed the broken part from the upper rack. I then replaced the broken rack roller, inserted into the slide and screwed the rollers which hold the slide into the sides of the dishwasher.

Damaged rinse agent dispenser

  • Customer: Ralph from McMinnville OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
Unscrewed old one and installed the new one.

Leaking from the drain valve shaft

  • Customer: Daren from Villa Rica GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
It turned out to be an easier job than I thought it was going to be. Of course, I was still a bit surprised it worked right and didn't leak once I was done.

I started by taking off the servo that opens up the drain valve. I didn't think I could take out and replace the shaft seal from this position so I took the whole motor and drain assembly out by loosening the sump and pump clamps. This allowed me to wiggle out the whole mechanism. One plug and a ground wire had to be undone but that was it. The Push On Nut was the worst part - pain to take off - worse to get a new one on. I wasn't sure (still not) if I could get it in the right place. Once I got everything back together and the servo mount on it seemed to hold the nut in the right place.

I tested it and yelled "it doesn't leak!" my wife promptly said "Yet!".

We have run the dishwasher twice - so far - no leaks!

I couldn't have done it with out PartSelect's prompt service, diagrams, and part photos. I don't want to fix any more appliances but if I have to PartSelect is where I'll come for parts and diagrams.

Rack rusting

  • Customer: melissa from ferrum VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Took end caps off roller guides. Slid old out...slid new in...poped end caps back on...done. Too EASY!

broken off end caps, top would slide off, frustrating.

  • Customer: Paul from Blairs VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

COLLECTION CHAMBER COLLASPES

  • Customer: Carlos from Whittier CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Socket set, Wrench(Adjustable)
  • 4 of 7 people found this instruction helpful
I REMOVED DRAIN HOSE TO INSTALL 1 YR OLD DISHWASHER.INSTALLED IT FD WATER LEAK AT DRAIN HOSE. REMOVED IT, FOUND COLLECTION CHAMBER WAS COLLAPSED. THIS WAS A FACTORY BO-BO.COLLECTION CHAMBER IS MADE OF P.V.C. I ALSO HAD A PROBLEM WITH THE SUMP FILTER BALL. CALLED G.E. THE TOLD ME TO JUST PUT THE BALL IN THE CHAMBER,NOT, THE BALL HAS TO COME IN FROM THE TOP, REMOVING THE SPRAY ARM,SUMP COVER,MAJOR DISASSEMBLY.NOW I KNOW HOW TO COMPLETELY DISMANTLE A DISHWASHER.HOME DEPOT HAD NO IDEA WHAT I WAS TALKING ABOUT???NOW WORKS GREAT!!!!!!!!!!!!!!!

Dishwasher tub would not drain

  • Customer: Michael from McDonough GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 4 of 7 people found this instruction helpful
Pulled unit out from counter (never had dishwasher issues before) to see if there was anything obvious with wiring or anything. Noticed that some little piece on the bottom looked to have melted (later discovered to be the drain solenoid). Removed the obviously defective part and looked it up on line. Found the name of it on Part Select's website then started shopping for best price. Came back to Part Select because the price was the cheapest I could find. Two - Three days later received part and put it back on and had the dishwasher back in place and in use within about 10-15 minutes. Marking my first ever dishwasher repair. :)

Discharge of water when draining

  • Customer: Darryl from Adkins TX
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
This seems to be a simple repair, but the push on nut is difficult to remove. Ended up damaging the case, so I am going to buy another dishwasher. If you plan to repair, make sure you pull the unit out to have plenty of room to work with.

Rinse Agent Tank Leaks

  • Customer: Paul from Lithia FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
The following steps were performed: 1) Disconnect power to the dishwasher 2) Unscrew all the screws on the inside of dishwasher door. 3) Remove outside plate on bottom of dishwasher. 4) Separate the dishwasher door after all screws are removed and pull out the old dishwasher rinse agent tank. There is a screw that needs to removed that holds the tank in place as well. 5) Snap in the new rinse agent tank and tighten screw in that holds tank in place. 6) Gently put the inside door back in place. Make sure all the holes line up correctly. 6) Put back the bottom plate of dishwasher. 7) Turn on the power again. You have now completed the repair.

Water drip, door gasket and rack parts

  • Customer: steve from Bedford IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
I had a slow drip under the dish washer that originated from the solenoid shaft. The replacement o ring fixed it up. While I had it pulled out I replaced all the door seals and top rack rollers.

I ordered the parts on a Thursday evening and received them on Friday. WOW now that's fast! The parts came from Illinois and I live in Indiana so that might have helped but I was very surprised and glad for the quick service. I would defiantly order from Parts Select again. Thank you!

A rack roller broke into pieces. The top tray didn't slide properly.

  • Customer: Sharon from Southlake TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.

Dishwasher was leaking

  • Customer: Jon from Henderson NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!

Disrack was getting rusty

  • Customer: Nelson from Oroville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

Missing wheels

  • Customer: Felix A from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Inserted wheels on socket and then into the dishwasher rack.

Severe lwater leak around door

  • Customer: Merle from Boulder CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!
All Instructions for the HDA3500N10BB
76-90 of 510