Models > HDA3400G02WW > Instructions

HDA3400G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G02WW
676-685 of 685
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Upper Rack difficult to open

  • Customer: Dan from Oak Ridge NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The initial problem was that the top rack was difficult to slide out. I purchased a new set of upper rollers. In order to remove the roller you must slide it off the rail. To do this, you must first remove the end cap. I broke the end original end cap trying to do this. The new roller installation was simple. So was the installation of the new end cap. Simply press it on.

The dishwasher was not draining

  • Customer: Marcus from Argyle TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The machine had been running sluggish for a while. Replaced the pump awhile back, but it still wasn't draining good. Then it quit draining. The solenoid is mounted on the pump, two screws and a clip on the valve door shaft come off. The new one is easy to put on. Caution: many of these appliance people say that timers are often needlessly replaced, but when I looked at the old solenoid, it looked like a meltdown had occurred. It was not worn out, it had overheated. Checked out timer and found cause. The gear on the motor shaft was partially stripped, causing drain valve to stay open too long. New timer, solenoid, pump-ten years old and never ran this good.

how to remove rack

  • Customer: Anton from Middletown CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
go to google..replace ge dishwasher rack.. very clear way to pry tab with a quarter and rotate end cap.. remove/replace rack reverse install end cap

Upper dish tray was rusted

  • Customer: JERREL from PORTLAND OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the tray with a new one. Would have been no problem at all, if I had realized how the track end clip was supposed to go. I thought the release had to be pushed toward the lock, but it needs to be pushed away from it. This sounds confusing, but when you look at it, it may be more clear to you.

Roller axle kits broken

  • Customer: Scott from Gainesville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just watch the video and you will be fine. The only thing I would suggest is buying both your rack slide end caps because with the age of my machine they were brittle and cracked/broke where they were supposed to only bend. Spend the extra $.64 and you will be glad you did.

wheels of dishwasher (upper drawer) cracked off

  • Customer: JASON from GAITHERSBURG MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The PartSelect video told me to take the end caps of the track and simply snap the old wheels off. It was easy. I popped the new wheels on, put the rack back on, and reattached the end caps. I was surprised by how simple it was to repair a major kitchen appliance.

rollers broke

  • Customer: James from Simpsonville SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed new ones as per instruction

roller broke

  • Customer: Sam from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
follow your video instruction. very simple.

Dishwasher racks were replaced in the first order.

  • Customer: Philip from Parkland FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
When I received the first order the lower rack didn't fit because it wasn't wide enough. Your people replaced the rack and now all works in good fashion. Thx, Phil

Lower dishrack rusted

  • Customer: susanne from Moorpark CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Instructions for repairs. Remove old rack from dishwasher. Stop, have a beer. Open packing box. Remove new dishwasher rack from box. Rest. Have another beer. Slidey old thingamajig rack ouy from dithwather. Shove into packing box. Figure out where you put the new rack. Pick up new rack, put new rack on countertop. Hav anoder beer. Put nw wreck in dithwather. Take bx & bee botluls to trash. Take nap. :>) S.
All Instructions for the HDA3400G02WW
676-685 of 685