Models > HDA3400G02WW > Instructions

HDA3400G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G02WW
646-660 of 685
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

DISHWASHER WAS NOT DRAINING - STANDING WATER

  • Customer: John from Absecon NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
FOLLOWED THE VIDEO ON THIS SITE, REPLACED PART IN UNDER 10 MINUTES, RAN A CYCLE - P-E-R-F-E-C-T !!! THANK YOU SO MUCH - I AM SOOOOO NOT A DIY TYPE PERSON, BUT THIS WAS EASY!

miss wheels

  • Customer: Martha from Fort Worth TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

Lower dishwasher wheels broken/ deteriorated.

  • Customer: Stephen from Madison IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered parts from Parts Select, and replaced lower roller wheels. The diagrams/ drawings were key in ordering the correct replacement parts - thanks

Broken front upper rollers

  • Customer: H. M. from Waskom TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
In the video, they must have been removing new parts from a new machine. 7 year old parts do not come off so easily. You may need a screw driver (I used a plain old dinner knife) to pry up the prong. (Parts went flying as they broke off for good!) I had to use a wrench to get the roller off. BUT, the new part slipped on like "greased lightening." Sooooooo, watch the video, follow their step by step instructions, but be prepared with a tool or 2 since the only reason you are doing this is because it is OLD!!!

Axles on wheels broken

  • Customer: Patrick from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pop the new wheels on. The rear wheels are thinner than the front wheels so rack slides in smoothly

Not draining completely/foaming out door

  • Customer: Barry from Wrentham MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Watched the video, replaced the recommended part EASY-Done Would not hesitate on any other appliance repairs in the future Great site!

Small trail of water leaking from bottom of door.

  • Customer: Max from Newton MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After examining the lower baffles, it was evident that their grooves were bent out of shape and warn. They were simple to pop out, I cleaned the area and popped in the new baffles. Unfortunately, the leak still happened. Upon further examination, the corners of the gaskets where they rubbed against the baffles also looked worn. So I ordered a replacement gasket and gasket insert and just installed them. Problem solved. The instructional videos were exceptionally clear. I'm not particularly handy. If I had not seen the videos online before ordering the parts, I would have called a repair service and spent $150+ more.

Door latch would not lock dishwasher door

  • Customer: Betty from Flintstone GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

there weren't front dishrack rollers

  • Customer: matthew from hillsboro IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
the parts were delivered quickly. i removed the lower rack. the rollers were ready to install. they simply snapped on the post. Done! i placed the rack back in its place and they fixed the problem.

The dishwasher was not filling with water

  • Customer: Missy from Milton VT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This repair was not difficult except that the part was hard to get to. You need to lay on the ground and the space is small to fit the tools in. It was especially difficult to squeeze the hose clamp on and off. If you are the handy sort and would not be intimidated by pulling the dishwasher out (like I was), then I recommend doing that. Changing the actual part was a breeze and self explanatory. Be sure to shut off the power and water supply to the dishwasher. Bring a towel to soak up residual water in the hose. Watch the video on this site, it was exactly what I needed to see! I was able to fix my mom's dishwasher! What a great feeling!

wash water not entering

  • Customer: James from BOULDER CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
took the front covers off, used om meter as suggested after disconnecting the wire plug. discovered infinity, so as suggested, determined the valve defective. Ordered over the new valve from this company. After it arrived, took the old valve off by removing it from the bracket. Used the pliers to take the hose off, then unscrewed the supply hose by usung the adjustable wrench. Took the old valve to my shop vise to hold it firmly, then unscrewed the fitting, wrapped the tape suggested and installed it on the new valve. Took it back to the dishwasher, screwed the supply hose on, slipped the hose on and the clamp, turned on the water to check for leaks. Found non, so installed the valve on the frame, turned on the power and checked for filling. Itfilled fine and operated like it was supposed to. Put the front covers back on, and enjoyed praise from wife!!!

water inlet valve stuck open (frozen??)

  • Customer: Richard from Bay Village OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!

dishwasher does not drain

  • Customer: tom from bend OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working

Water laid in bottom of dishwasher and turned black after end of cycle

  • Customer: Robert from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove grid at inside at very back. At center under grid is the valve, unscrew CCW, and replace with new valve. Replace grids.

did not pump out all the water before drying

  • Customer: james from ham lake MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
looked up the model no. on partselect web site and they discribed several diagnoses for different problems.they gave a 19% probability for a bad valve and nut. i removed the cover and the nut valve and the valve looked pretty bad. i ordered a new part and delivery was very good.i replaced the part and that took care of my problem. i was very happy with the whole repair.
All Instructions for the HDA3400G02WW
646-660 of 685