Models > HDA3400G00WW > Instructions

HDA3400G00WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G00WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G00WW
76-90 of 731
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

WATER LEAK IN RUBBER CONNECTOR PIN HOLE AT SEAM

  • Customer: Allan from Stony Point NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling Housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip., rescrewed in the new rubber connector. (
HINT- used petrolem vasaline on the rubber connector base for a water tight fit) . reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. turned water back on.

All worked at well.

Motor was jammed, just heard a humm from unit.

  • Customer: Brook from Madison WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT

  • Customer: Raymond from ansonia CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Water stays in the bottom because the solenoid burned out.

  • Customer: Guorong from Novi MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts.
A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.

One of my top rack rollers had broken and the rack could not hold any weight

  • Customer: Louis from Fairfield CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

Leaking water at the solenoid valve stem

  • Customer: Gordon from Stone Mountain GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

dishwasher filled base with clean water when not in use

  • Customer: Harvey from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 6 of 8 people found this instruction helpful
The repair was really easy. I ordered the part needed after looking at this website. I figured out the problem by looking into the forums. I ordered the part. It came within several days. I got home from work and after dinner pulled the dishwasher from under the kitchen counter. It was easy to do. I flipped the dishwasher on its side. Then removed the old part. It had a water inlet that required a fitting to be loosened with a wrench. It also had a flexible water fill that was attached with a cable clamp. (Remember to turn your water supply off first!) The wiring was disconnected by a simple harness. Four bolts had to be removed to pull the part off of the dishwasher body.

Installation was the reverse of this process. Have been using for a week now and the problem is corrected. Doing business with Parts Select is awesome. I know that over the last several years I have saved tons of money and learned that I can fix nearly any appliance by viewing this website.

Dishwasher was leaking

  • Customer: Ira from Fort Edward NY
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 5 of 5 people found this instruction helpful
Disconnected the electrical, water supply and drain. Pulled unit out from under counter, tipped it on its side and replaced the motor/pump unit. tipped it back on its legs put it back under the counter connected the water supply, drain and electrical. All went well. The unit performs as it should. it took about two (2) hours without rushing through it.

The spray arm's tower was broken off

  • Customer: James from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Unscrewed the old spray arm (I needed pliers but you may not need them)and screwed on the new spray arm.

Broken Roller

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

Dishwasher began leaking at the end of cycle

  • Customer: GEORGE from CRANSTON RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Remove old left and right corner tub baffles, make certain area where the new baffles are to be inserted is clean and free of any debris. Gently press new baffles in to each corner. Remove old gasket insert and replace with new. Tell wife the job was a three hour ordeal that require advanced skills to complete!

Replacement of the Dish Racks due to corrosion

  • Customer: Raymond from Rochester NY
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
The top dish rack was not an exact replacement, the side shelf did not fit and the center spray did not fit. I ran into much more trouble removing the the top rack than I had thought. I used the old wheels and it finally went on but the other mentioned problems remained.

Motor/Pump Siezed - Only Getting A "Humming" Sound

  • Customer: Scott from Oklahoma City OK
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 5 of 6 people found this instruction helpful
Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had never done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.

Water leaking from the bottom center of the front door

  • Customer: Danny from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
The lower right and left tub baffles just slip in, no tools required. For the front door gasket; a) removed the backside of the front door by removing the door screws. You need to manipulate the front door latch to remove the panel. b) remove the existing gasket, replace with new gasket. The short 4" gasket was missing, which is why it was leaking in the first place. Replaced it with the new one. Reassembled and tested. Thanks to Parts-Select for a great experience, very well done site.

Dishwasher is 5 yrs old. Never really washed right sometimes had sand on the top rack. 1 month ago started leaking from bottom put towels down and did only 1 load a day. Floor starting to rot my husband pulled out the dishwasher saw where it was leaking took the piece out saw it was cracked and repl

  • Customer: Beatrice from Medford NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 5 of 6 people found this instruction helpful
Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!
All Instructions for the HDA3400G00WW
76-90 of 731