HDA3400G00WW Hotpoint Dishwasher - Instructions

I ordered the corner baffles and installed them in the corners in just minutes. Repair company quoted me about $100 if they had the parts on the truck. If they had to come back it would be another service call. Did the repairs my self for $24 with shipping charges. Happy Customer

looked up the model no. on partselect web site and they discribed several diagnoses for different problems.they gave a 19% probability for a bad valve and nut. i removed the cover and the nut valve and the valve looked pretty bad. i ordered a new part and delivery was very good.i replaced the part and that took care of my problem. i was very happy with the whole repair.

follow your video instruction. very simple.

The machine had been running sluggish for a while. Replaced the pump awhile back, but it still wasn't draining good. Then it quit draining. The solenoid is mounted on the pump, two screws and a clip on the valve door shaft come off. The new one is easy to put on. Caution: many of these appliance people say that timers are often needlessly replaced, but when I looked at the old solenoid, it looked like a meltdown had occurred. It was not worn out, it had overheated. Checked out timer and found cause. The gear on the motor shaft was partially stripped, causing drain valve to stay open too long. New timer, solenoid, pump-ten years old and never ran this good.

My machine stopped leaking after I simply massaged the door gasket and cleaned the baffles. I did order the necessary parts, they arrived in a very timely manner and the process was painless. After watching the video for both the door gasket and the tub baffles, when my machine decides to leak again, I will be ready to install new parts. As a snow bird, my machine sits idle for 6 months and I think things tend to dry out. Wonderful experience in ordering and video watching.

Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working

When I first noticed my unit leaking I noted that the leak was dripping right in the middle. So, I went straight to this web site with my model number and the 1st part I saw was for a Gasket Insert which is a small piece that completes the sea. I received that part in 2 day and did the repair and I still had leakage. I went back on the web site and looked further and came across info for the Corner Tub Baffles. I did not even know there were there. I removed mine and it was very obvious that the original Baffles were very worn and wrapped. In addition, the unit was quite filthy. I ordered the two replacement baffles. The parts arrived in two days, did the minor repair and now I have no leaks.

The PartSelect video told me to take the end caps of the track and simply snap the old wheels off. It was easy. I popped the new wheels on, put the rack back on, and reattached the end caps. I was surprised by how simple it was to repair a major kitchen appliance.

Replaced the water-fill solenoid valve.

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Watched the on-line video. It was great and made the replacement job easy. Without the video, I probably would have broken the plastic end caps while trying to take them off. I highly recommend watching any available repair videos.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

I followed the video instructions..I was concerned that the end pieces would be a problem, so I purchased replacements also, but they came off with no problem - thanks to the video.They only cost about $2.50, so I will keep them in stock in case I need them at a later date.Without the video, it probably would have driven me nuts trying to figure out how to remove the end pieces, but when you see it done, it was simple.....Thanks Loads.

I cleaned all the drains in the dishwasher and the drain in the garbage disposal that leads from the dishwasher. I also removed the piston and nut assembly and tried cleaning it but the dishwasher still did not drain. I was using a wet vac to empty the standing water after the cycle completed. I bought the new piston and nut assembly. It arrived in 24 hours. I unscrewed the 4 screws in the back of the dishwasher that held the screen that covered the assembly, used my hand to unscrew the piston and nut assembly, screwed in the new part and replaced the screen and 4 screws. It completely fixed the problem.

Removed rack by twisting and pulling off the plastic ends of the upper roller tracks. Removed old wheels from track and discarded. Removed old wheel assemblies from rack with fingernail. Replaced wheel assemblies on rack with the new ones. Alligned rack with tracks and pushed back into the dishwasher. Replaced plastic track ends with opposite action required for removal. Job completed.