Models > HDA3400G00BB > Instructions

HDA3400G00BB Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G00BB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G00BB
46-60 of 731
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

leak at shaft seal

  • Customer: DAVID from ADAMS MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
The shaft pulled out of the housing when I tried to get the push nut off. I had to take the pump housing out in order to get the shaft lined up with the valve when reassembling. In the end, the shaft had so much slop that no seal could keep it from leaking. Time for a new dishwasher.

plastic hinge arm link broke causing door to flop open

  • Customer: Margaret from Meridian MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 13 of 17 people found this instruction helpful
First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Replace valve

  • Customer: James from Hartsel CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 12 people found this instruction helpful
Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

spray arm was cracked and the top part kept spraying off

  • Customer: sheila from dyersburg TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
just unscrewed it from the dishwasher with my hand and put the new one back on the same way

Dishes were coming out with nasty film and chunks - gross!

  • Customer: Russell from Portage MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
Read about somebody else with the same problem and ordered the check valve. 4 screws off, twist out old valve, twist in new valve, 4 screws back in. Now dishes are see-yourself clean.

Dishwasher would not drain.

  • Customer: Jonathan from Athens GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
I removed the four screws of the filter frame exposing the check valve (piston and nut assembly) . I unscrewed the old check valve and replaced it with the new one.

22 YR OLD DISHWASHER WOULD NOT PUMP OUT WATER

  • Customer: Joseph from Lowell MA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 11 of 14 people found this instruction helpful
22 YEAR OLD DISHWASHER ... NOT WORTH REPAIRING I THOUGHT SO I PULLED IT OUT TO DISPOSE OF IT. BEFORE I DID, I WENT ONLINE TO SEE IF ANY PARTS WERE STILL AVAILABLE...TO MY SURPRISE PARTSELECT.COM HAD IT ALL!
MY PROBLEM WAS A PLUGGED CHAMBER LOCATED ON REAR WALL OF UNIT.
A 20 MINUTE REPAIR ONCE THE NEW PART ARRIVED.
PART ARRIVED IN 3 DAYS BUT WAS BROKEN INSIDE OF PKG. I CALLED AND THE OPERATOR APOLOGIZED PROFUSELY... SHE TOLD ME TO KEEP THE DEFECTIVE AND EXPLAINED MY CC WOULD temporarily BE CHARGED FOR REPLACEMENT BUT AS SOON AS THEY RECEIVED A CREDIT FROM SUPPLIER MY CREDIT WILL APPEAR ON MY CC STMT. I HAD A REPLACEMENT THE FOLLOWING DAY...
WHAT A COMPANY!!!!

Old Motor Seized

  • Customer: Gordon from Ogdensburg NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 11 of 15 people found this instruction helpful
Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

tub corner baffles were falling apart

  • Customer: ROBERT from GLOBE AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 9 of 9 people found this instruction helpful
I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

dishwasher was not draining left water in bottom of machine the drain solenoid was melted.

  • Customer: Eric from Golden CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.

Dishwasher rack was rusting and partially broken

  • Customer: John C from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

Motor seized on 1990 GE dishwasher

  • Customer: DAVID from UNION MILLS NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 10 people found this instruction helpful
The motor seized up on my 1990 GE Dishwasher
Repair would cost 360. Replacement about 600
I ordered the motor and pump from PartSelect for 137..44
Remover the under counter washer (it‘s very light) and removed the water and drain line and disconnected the power. Turned the washer on it’s top to access the motor and pump and removed the electrical plug in lines, and the clamps holding the pump on to the connections. Replaced it with the new motor and pump, reconnected the electrical plug ins, added an adapter hose part, tightened the original clamps then reconnected the water, drain and electrical connections and reinstalled the washer. All in about an hour, The only glitch was the grounding screw for the ground wire on the motor. The screw was too long to tighten. Substituted the original shorter ground screw from the old motor, and that worked fine. Only used 4 parts from the large assortment of parts supplied.
Immediately ran the washer through a cycle, all worked perfectly.

Dishwasher was leaking between the pump motor and pump assembly

  • Customer: Jesse from Royal Oak MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

accumulation of dirt in behind screen in back of washer

  • Customer: William from Belmar NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 11 of 16 people found this instruction helpful
Pulled dishwasher out. Unscrewed 4 screws holding body valve, disconnected 2 hoses and replaced valve, put machine back together in reverse order.

dripping from bottom door

  • Customer: Bill from Surprise AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Since i was not sure which gasket has failed, i replaced all 4 considering the age of the dishwasher,( 2 are corner baffles ). The only time i was scratching my head was installing the gasket insert. No one mentioned to overlap or not, so i did overlap and crossed my fingers. After several cycles there is no dripping so i guess overlapping about a 1/2 inch is the way to do it. And i would suggest cleaning the gasket groove in the bottom corners really good. Good luck, bill
All Instructions for the HDA3400G00BB
46-60 of 731