Models > HDA3400F00WW > Instructions

HDA3400F00WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400F00WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400F00WW
46-60 of 742
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water was leaking form around drain valve shaft.

  • Customer: Barry from Knoxville TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
I called the repair guy, and he told me I'd have to replace the motor/pump assembly. He said he could do it for around $250 to $300. I logged onto this website for a look and saw the seal available. After reading the other responses, I figured with a seal and the cheap push-nut (that sometimes gets mangled upon removal), it would be worth a try.
I pulled the dishwasher partly out from under the cabinet; disconnected the front support mount, the drain hose, and the two water boots; dropped the motor/pump assembly; removed the solenoid; removed the e-clip, push-nut, shaft, and old seal; and then reinstalled everything. The hardest part of the repair was the tight working conditions. I wonder how many people pay hundreds of dollars because of this $15 part.

leak at shaft seal

  • Customer: DAVID from ADAMS MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
The shaft pulled out of the housing when I tried to get the push nut off. I had to take the pump housing out in order to get the shaft lined up with the valve when reassembling. In the end, the shaft had so much slop that no seal could keep it from leaking. Time for a new dishwasher.

Replace valve

  • Customer: James from Hartsel CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 12 people found this instruction helpful
Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

plastic hinge arm link broke causing door to flop open

  • Customer: Margaret from Meridian MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 16 people found this instruction helpful
First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Dishwasher would not drain.

  • Customer: Jonathan from Athens GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
I removed the four screws of the filter frame exposing the check valve (piston and nut assembly) . I unscrewed the old check valve and replaced it with the new one.

Dishes were coming out with nasty film and chunks - gross!

  • Customer: Russell from Portage MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
Read about somebody else with the same problem and ordered the check valve. 4 screws off, twist out old valve, twist in new valve, 4 screws back in. Now dishes are see-yourself clean.

spray arm was cracked and the top part kept spraying off

  • Customer: sheila from dyersburg TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
just unscrewed it from the dishwasher with my hand and put the new one back on the same way

Dishwasher rack was rusting and partially broken

  • Customer: John C from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

accumulation of dirt in behind screen in back of washer

  • Customer: William from Belmar NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 11 of 15 people found this instruction helpful
Pulled dishwasher out. Unscrewed 4 screws holding body valve, disconnected 2 hoses and replaced valve, put machine back together in reverse order.

Old Motor Seized

  • Customer: Gordon from Ogdensburg NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 11 of 15 people found this instruction helpful
Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

tub corner baffles were falling apart

  • Customer: ROBERT from GLOBE AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 9 of 9 people found this instruction helpful
I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

dishwasher was not draining left water in bottom of machine the drain solenoid was melted.

  • Customer: Eric from Golden CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.

Dishwasher was leaking between the pump motor and pump assembly

  • Customer: Jesse from Royal Oak MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 9 people found this instruction helpful
The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

Dishwasher solenoid overheated

  • Customer: Matt from Summerfield NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 12 people found this instruction helpful
If you are replacing an overheated solenoid that had the plastic melt, don't forgot to order a armature and link as well. I made this mistake and had to wait another week to fix the dishwasher. The repair wasn't too bad. The most time consuming part was putting the E-clip retainer ring back on the diverter shaft. Tipping the dishwasher back some really helped for me to have more room to see and work with.

dripping from bottom door

  • Customer: Bill from Surprise AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Since i was not sure which gasket has failed, i replaced all 4 considering the age of the dishwasher,( 2 are corner baffles ). The only time i was scratching my head was installing the gasket insert. No one mentioned to overlap or not, so i did overlap and crossed my fingers. After several cycles there is no dripping so i guess overlapping about a 1/2 inch is the way to do it. And i would suggest cleaning the gasket groove in the bottom corners really good. Good luck, bill
All Instructions for the HDA3400F00WW
46-60 of 742