Models > HDA2100N10WW > Instructions

HDA2100N10WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2100N10WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2100N10WW
226-240 of 240
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Consistent slight leaks at door corners.

  • Customer: Mike from Salem OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
There is no repair easier than this! Simply remove the decayed gaskets and replace with new. No tools, no glue, no nothin'.

Upper dish tray was rusted

  • Customer: JERREL from PORTLAND OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the tray with a new one. Would have been no problem at all, if I had realized how the track end clip was supposed to go. I thought the release had to be pushed toward the lock, but it needs to be pushed away from it. This sounds confusing, but when you look at it, it may be more clear to you.

how to remove rack

  • Customer: Anton from Middletown CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
go to google..replace ge dishwasher rack.. very clear way to pry tab with a quarter and rotate end cap.. remove/replace rack reverse install end cap

water leak around door

  • Customer: D M from Fuquay Varina NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
open packages of baffles, installed per video, done, no leak!

Upper Rack difficult to open

  • Customer: Dan from Oak Ridge NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The initial problem was that the top rack was difficult to slide out. I purchased a new set of upper rollers. In order to remove the roller you must slide it off the rail. To do this, you must first remove the end cap. I broke the end original end cap trying to do this. The new roller installation was simple. So was the installation of the new end cap. Simply press it on.

water leak from underneath the unit

  • Customer: ANTHONY from NEW EGYPT NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
After shutting off the water and switching off the electric, I removed the lower panels and disconnected both. I then pulled the unit out and set it on its back. I removed the related hoses and moved the pump to the side. Using a 2" X 6" piece of PVC pipe, I removed the wash arm rubber connector which had a small slit in it and installed the new one with the PVC pipe. After reconnecting the hoses and reversing the process, I powered up the unit resulting in another successful repair with the help of Parts Select.com.

Right door spring broke

  • Customer: Heidi from North Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took lower panel off with screwdriver. Removed old spring. Attached new spring. Very easy, and I'm a woman. LOL

Water leak from gate (diverter) valve

  • Customer: Robert from Oak Island NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Read Joseph from Livermore, CA for good instructions. I took a camera phone photo for reference before I started. Should have taken another photo half way thru. Probably put the push-on-nut on backwards as it didn't 'lock' in - had too much play in the shaft, would have leaked. Impossible to get nut back off in good shape. I put original mangled push-on-nut on also - it added enough tension to eliminate play in the shaft. No leak..but lucky. Go ahead, you can do this repair for under $20.

Dishwasher racks were replaced in the first order.

  • Customer: Philip from Parkland FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
When I received the first order the lower rack didn't fit because it wasn't wide enough. Your people replaced the rack and now all works in good fashion. Thx, Phil

Lower dishrack rusted

  • Customer: susanne from Moorpark CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Instructions for repairs. Remove old rack from dishwasher. Stop, have a beer. Open packing box. Remove new dishwasher rack from box. Rest. Have another beer. Slidey old thingamajig rack ouy from dithwather. Shove into packing box. Figure out where you put the new rack. Pick up new rack, put new rack on countertop. Hav anoder beer. Put nw wreck in dithwather. Take bx & bee botluls to trash. Take nap. :>) S.

leaking drain valve. note i took the disherwasher out about six months to remodel the kitchen it wasn't leaking when i took it out , but being out so long with out water in it, it started to leak when i put it back in !! !!

  • Customer: ronald from pompano beach FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
i replaced the drain seal without removing the dishwasher as far as the push on nut i had to use a round punch to open the tabs a little.. i also used Vaseline to hold the c clip in place to snap it in with a screwdriver

My dishwasher would not drain.

  • Customer: Terrence from New Castle DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.

Dishwasher was leaking out the left front

  • Customer: Anita from Boon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the corner baffles and installed them in the corners in just minutes. Repair company quoted me about $100 if they had the parts on the truck. If they had to come back it would be another service call. Did the repairs my self for $24 with shipping charges. Happy Customer

leaking during cycles

  • Customer: Bonnie from Sebring FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My machine stopped leaking after I simply massaged the door gasket and cleaned the baffles. I did order the necessary parts, they arrived in a very timely manner and the process was painless. After watching the video for both the door gasket and the tub baffles, when my machine decides to leak again, I will be ready to install new parts. As a snow bird, my machine sits idle for 6 months and I think things tend to dry out. Wonderful experience in ordering and video watching.

Leaking

  • Customer: Valerie from Bedford TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
When I first noticed my unit leaking I noted that the leak was dripping right in the middle. So, I went straight to this web site with my model number and the 1st part I saw was for a Gasket Insert which is a small piece that completes the sea. I received that part in 2 day and did the repair and I still had leakage. I went back on the web site and looked further and came across info for the Corner Tub Baffles. I did not even know there were there. I removed mine and it was very obvious that the original Baffles were very worn and wrapped. In addition, the unit was quite filthy. I ordered the two replacement baffles. The parts arrived in two days, did the minor repair and now I have no leaks.
All Instructions for the HDA2100N10WW
226-240 of 240