Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HDA2000Z07WH > Instructions

HDA2000Z07WH Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000Z07WH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000Z07WH
631-645 of 669
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken lower wheel ion lower dishwasher rack

  • Customer: carole from Libertyville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Upper basket roller broken

  • Customer: Guntis from Sugar Grove, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the on-line video. It was great and made the replacement job easy. Without the video, I probably would have broken the plastic end caps while trying to take them off. I highly recommend watching any available repair videos.

Small leak at the bottom of dishwasher

  • Customer: Harry from Bayside, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

dishwasher not draining

  • Customer: Eric from Summerville, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was really easy just like the repair video, but you have to lay on the floor. Unfortunately, the problem wasn't the solenoid, but the pump/motor assembly. Be sure to check the solenoid operation before replacing (making sure it is cycling). It might be the pump/motor assembly. Good luck!

Rollers wore out

  • Customer: Joe from Langhorne, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video instructions..I was concerned that the end pieces would be a problem, so I purchased replacements also, but they came off with no problem - thanks to the video.They only cost about $2.50, so I will keep them in stock in case I need them at a later date.Without the video, it probably would have driven me nuts trying to figure out how to remove the end pieces, but when you see it done, it was simple.....Thanks Loads.

Leaking Dishwasher

  • Customer: Eugene from Port Saint Lucie, FL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replacing the two corner baffles was the third attempt to stopping the leak. I first replaced the door seal without removing the inner door and the leak did not stop. Then I removed the inner door, reinstalled the door along the bottom and added the small seal required at the lower center portion which is separate than the longer door seal. Still leaked! Then I replaced the corner baffles and alas., the leak stopped. I would recommend that all seals be replaced at the same time. Total cost about $40.00 and can easily be done in one hour or less. I ordered the parts And they arrived remarkably in les than 24 House with regular delivery. Very pleased with Parts Select instructions and service!

Roller axles worn down

  • Customer: Dean from Mountain Home, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed rack by twisting and pulling off the plastic ends of the upper roller tracks. Removed old wheels from track and discarded. Removed old wheel assemblies from rack with fingernail. Replaced wheel assemblies on rack with the new ones. Alligned rack with tracks and pushed back into the dishwasher. Replaced plastic track ends with opposite action required for removal. Job completed.

Pump was leaking from the shaft seal

  • Customer: Anthony from Mechanicville, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.

Upper and lower racks had badly rusted.

  • Customer: George from Krum, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the YouTube video about removing the end tabs on the upper rack then simply removed them with a flat head screw driver. Then, after replacing the rack, I re-inserted the tabs using the screw driver. as shown in the video. There's really nothing to it after watching the video, which is about 2 minutes long.

Dishwasher was leaking behind the door

  • Customer: Teddy from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
First open the door and look at the corner tub baffles. They are in the bottom corners where the door seals with the tub and they look alike. Remove and replace one at a time making note of the orientation. Make sure they are firmly seated in the bottom and close the door and enjoy.

Not Cleaning Properly

  • Customer: Kevin from Torrance, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Dishes were not being cleaned, so the first thing I did was take the float cover off and cleaned the soap gunk off (it was getting stuck open). That solved about 50%. I could tell that the spray arm was gunked (and partially clogged) so I replaced it with this one. A pipe wrench got around the base and I torqued it loose and off, cleaned the inside with a paper towel, and I put the new one on hand tight. Dishwasher works like new again.

Water leaking under dishwasher.

  • Customer: Louis from Dover, DE
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I first shut off the power to dishwasher, then shut off water and disconnected the water supply line. Then pulled the washer out from under counter and layed it face down. Undid the hose clamp from sump housing and clamp for wash arm rubber connector. Disconnected screw for the motor brace. Motor swung out of way. Pulled out sump housing and cleaned the edges of the hole. Pushed housing threw bottom and got it to seat in the groove inside the washer. I then unscrewed the rubber for the wash arm and cleaned those areas too. Screwed the new connector on and made it tight, old one was loose. Moved the motor back and reconnected hose clamps and reattached the motor support bracket. Stood washer back up and pushed it back under the counter. Reconnect water line and turned water back on to make sure it was not leaking. Turned power back on to washer. Then poured a large pot of water into washer and turned on and kept checking for leaks but there were none. Finished putting cover plates back on and the washer was done. Then I had to replaced some of the flooring that was damaged from the leaking of these two parts.

Broken clips

  • Customer: Michael from Novi, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Clipped in new wheels and clips

Tub leaking at base of door

  • Customer: David from Parish, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Really simple. Remove old corner baffles by just lifting out and replace with new. Close door to insure the door seal aligns with the new baffles and good to go.

knob timer was broke.

  • Customer: Dortha from Fort Smith, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took it out of package and replaced it with new knob.Very simple.
All Instructions for the HDA2000Z07WH
631-645 of 669