HDA2000Z07WH Hotpoint Dishwasher - Instructions

Removed bottom panel unplugged wires removed two screws removed it then replaced it

In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.

bottom rack was easy. on the top rack, I used as quarter to release the plastic ends on the two sliders. Google had video showing how to do this using a quarter.

At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.

within 5 minutes.Great site for information and parts

The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in the 4 years we have owned the house.

I thought to myself, this is going to be easy, but I hit a couple bumps getting the end caps off. I just watched the video and it was great and helped me be sucessful. The only thing that would have helped was instructions on how to put the end caps back on! david

Removed the tray from its rails. Removed axle clips fro tray and replaced with new axles. Put tray back in rails and I was done. Works like

To remove the old upper rack, I needed to use a screw driver to snap out the plastic end stops. That took a little time, because my dishwasher is located in a corner of my counter/cabinets, making the stop on the right very difficult to get to. Once that was done, I just slid the old rack out, the new rack in and replaced the stoppers. I was very impressed with your service and received my order in less time than stated on my order form. Will definitely use you again and recommend you to others!

The upper rack fit, but the rack differed from the original to the extent that glasses that normally could be washed on the upper rack no longer fit, and the inverted upper rack "funnel" is further from the water stream nozzle reducing the effectiveness of cleaning on the upper rack. The rack rests significantly higher in the machine than the original.

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.