Models > HDA2000Z02WH > Instructions

HDA2000Z02WH Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000Z02WH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000Z02WH
61-75 of 594
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The seal for the drain valve was leaking.

  • Customer: mary from orlando FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
I removed the front bottom panels to give me access to the Solenoid area. I did not take out the dishwasher from the cabinetry. I removed the screws holding the solenoid assembly and the C clip holding the hand fan shaped white nylon thing onto the valve shaft. I slipped these to the side. Then I cut through and removed the push on nut with a wire snipper plier. Then I used a knife blade tip to pick out the black seal. I then slipped the new seal onto the shaft, being careful that the flat side was outward, and slid it down the shaft and , with my fingernail, pushed it completely flush into position. The biggest challenge was the push on nut. It does not push on easily and must have the lips pointed outward. It required the use of a 3/8" diamater tube slipped over the shaft to tap the nut down the shaft. This caused the shaft to push into the pump housing, which caused the valve to bind. So I used a vice grip to pull out on and hold the shaft while I tapped the push on nut with a flat head screwdriver. Then I just reversed the solenoid assembly removal. But , when I ran the dishwasher, it no longer leaked.

Timer would not allow water to unit

  • Customer: Tim from San Pedro CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 15 people found this instruction helpful
Disconnected power to dishwasher removed the seven screws that hold inside liner to door, and placed liner to the side.
Disconnected power leads to timer then removed the two screws that held the timer in place.
Installed new timer in revers order.
Also replaced the door gasket, one door liner screw, and the vent pad.
The most difficult part was keeping the door latch mechanisim in place when reinstalling the door liner.

WATER LEAK IN RUBBER CONNECTOR PIN HOLE AT SEAM

  • Customer: Allan from Stony Point NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling Housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip., rescrewed in the new rubber connector. (
HINT- used petrolem vasaline on the rubber connector base for a water tight fit) . reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. turned water back on.

All worked at well.

After twelve years the prongs on the top rack began to break and rust.

  • Customer: Jim from Wichita Falls TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
I ordered a replacement from partselect.com and received it in just three days. The only difficult part was deciding how to remove the white plastic end caps on the sliding rails. Finally, I took a small screwdrive and pried out the crimps in the metal, pulled the old caps out, inserted the new ones, and squeezed the metal together again using needle-nosed pliers. Nothing to it!
Note: The configuration of the new rack isn't exactly like the original (size and placement of the prongs differ somewhat) but it fits perfectly and works great.

Motor was jammed, just heard a humm from unit.

  • Customer: Brook from Madison WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT

  • Customer: Raymond from ansonia CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

One of my top rack rollers had broken and the rack could not hold any weight

  • Customer: Louis from Fairfield CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

Roller front shafts broken

  • Customer: EUGENE C from WICHITA KS
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Rack fits perfectly. The problem was removing the old Rail End Caps and then re-installing them. The are plastic and nealy impossible to remove. Finally after much coaxing was able to get them out. Howver, putting them back on was impossible. The long guide that nests inside the Rail could not be made to slide in so the latching hook could go into the rectangular hole. The hook prevented the long guide part from staying in the Rail on the upper end. Tried bending the long guide and it got it to nearly work, but the guide broke. It did not come completely off so left on and just pushed up after hook was put in hole. Doesn't seem to hinder operation. There was a plastic "tower" piece that must be for some other model. The Rack has a place for the Tower, but it wasn't part of the original Rack.

Old roller wheels were starting to stick due to cracking

  • Customer: Jeffrey from Springfield VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.

leaked and would not drain

  • Customer: Thomas from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
unscrewed bracket unplugged solenoid , pried off spring clip pulled nylon arm off and took off old push on nut. I had to squeeze the push on nut together with pliers from two angles to get it loose

Broken Roller

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

Dishwasher was leaking

  • Customer: Ira from Fort Edward NY
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 5 of 5 people found this instruction helpful
Disconnected the electrical, water supply and drain. Pulled unit out from under counter, tipped it on its side and replaced the motor/pump unit. tipped it back on its legs put it back under the counter connected the water supply, drain and electrical. All went well. The unit performs as it should. it took about two (2) hours without rushing through it.

Water wouldn't drain.

  • Customer: Lawrence from Silverdale WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
After disconnecting the supply and drain hoses I unscrewed the security screws and slid the unit out of it's space under the counter. I tipped the machine about 30-45 degrees to one side and examined the underside. I noticed a solenoid that appeared to control a valve leading to the drain tube. I cycled the washer through a wash cycle and noticed that the solenoid never activated. I removed the solenoid and found it filled with debris. I cleaned it out and reinstalled it, but it still did not function. I ordered the part from PartSelect.com because they had the clearest description of the part I needed. Delivery was quick and installation took only a few minutes. After hooking everything back up and sliding the machine back in place, it works like new.

Dishwasher is 5 yrs old. Never really washed right sometimes had sand on the top rack. 1 month ago started leaking from bottom put towels down and did only 1 load a day. Floor starting to rot my husband pulled out the dishwasher saw where it was leaking took the piece out saw it was cracked and repl

  • Customer: Beatrice from Medford NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 5 of 6 people found this instruction helpful
Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!

Corner baffles were in a bad shape

  • Customer: Keith from Avon Lake OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Old baffles lift out and new ones installed - very easy
All Instructions for the HDA2000Z02WH
61-75 of 594