Models > HDA2000G02WW > Instructions

HDA2000G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000G02WW
76-90 of 621
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaking water pump

  • Customer: John from Palatine IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 6 of 9 people found this instruction helpful
Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

2 rollers and end caps were broken were broken

  • Customer: Robert from Old Lyme CT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

Leaking water at the solenoid valve stem

  • Customer: Gordon from Stone Mountain GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

Water not draining from dishwasher

  • Customer: Teresa from Livermore CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
This is a great website. I ordered my part on Wednesday night and it arrived Saturday morning without paying any extra for shipping. Plus since I am a female, this website enabled me to easily and affordably make the repair myself without having to worry about a repair man trying to take advantage of someone that they think they can.

I first made sure that there was nothing stuck in the drain area inside of the dishwasher. That meant I had to bail out all the standing water and then unscrew the mesh cover from the bottom. Since there was nothing in there I ordered a new solenoid.

First I unplugged the dishwasher. Then I removed the screws with a screwdriver that held the bottom cover on the dishwasher. Once I could see the installed solenoid, I put together the pieces of the replacement solenoid that I bought so I was sure to install the new one correctly. That did not require any tools. Then I unscrewed the two screws that held the solenoid in place and removed the little metal ring from the shaft which was the last piece holding it in place. Getting that ring off was tricky. I ended up using a pair of tweezers to pull it off. After that I put the new part on and screwed it in with the two screws provided. The little metal ring went on much easier than the old one came off. I screwed the bottom cover back on and voila! my dishwasher was fixed.

Upper rack kept dropping from the wheels when we pulled it out

  • Customer: Joel from Cypress TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Broken Roller

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

at start of the wash cycle did not take in any water

  • Customer: wojciech from bayonne NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 5 of 7 people found this instruction helpful
very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.

the sump housing was worn out and leaked

  • Customer: sandra from colorado springs CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,

I had a water leak under the dishwasher

  • Customer: Hisham from Cambridge MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.

Rusted out racks

  • Customer: Everett (Jeff) from Altus OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Followed the instructions and it was easy. Made the washer seem brand new!...It is the best solutions for a small budget. We used CLR to wash out the washer workings and it really left a sparkle on the dishes... I am so glad you don't change the models so much that parts can't be exchanged when they wear...

Stinky Dishwasher

  • Customer: Jeremy from Hailey ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Holes in bottom of silverware basket

  • Customer: Jane from Clifton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

No water able to come in or out.

  • Customer: Victor from Raymond NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.

2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!

This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.

Dishwasher wouldn't drain

  • Customer: Jeffery from Sparks NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Dishwasher makes excessive noise when filling with water. Diagnosed by repairman.

  • Customer: Dan from Sachse TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
The repairman offered to fix the dishwasher at a cost of about $200 or supply the water inlet valve for $85. Google led me to PartSelect.com where I easily found the correct part for $45. I received the part in 2 days by FedEx ground.
The hardest part of the repair was removing the dishwasher from the cabinet. I took the dishwasher out a short distance to the patio where I replaced the water valve...about 10 minutes.
I then made a makeshift connection to an outdoor water hose and connected the electricity and ran the dishwasher while out on the patio through a short cycle to make sure of the repair and check for leaks.
Then reinstalled into the cabinet...total time about 2 hours.
Thank you PartSelect.com
All Instructions for the HDA2000G02WW
76-90 of 621