Models > HDA2000G02WW > Instructions

HDA2000G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000G02WW
616-630 of 648
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

roller broke

  • Customer: Sam from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
follow your video instruction. very simple.

The dishwasher was not draining

  • Customer: Marcus from Argyle TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The machine had been running sluggish for a while. Replaced the pump awhile back, but it still wasn't draining good. Then it quit draining. The solenoid is mounted on the pump, two screws and a clip on the valve door shaft come off. The new one is easy to put on. Caution: many of these appliance people say that timers are often needlessly replaced, but when I looked at the old solenoid, it looked like a meltdown had occurred. It was not worn out, it had overheated. Checked out timer and found cause. The gear on the motor shaft was partially stripped, causing drain valve to stay open too long. New timer, solenoid, pump-ten years old and never ran this good.

leaking during cycles

  • Customer: Bonnie from Sebring FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My machine stopped leaking after I simply massaged the door gasket and cleaned the baffles. I did order the necessary parts, they arrived in a very timely manner and the process was painless. After watching the video for both the door gasket and the tub baffles, when my machine decides to leak again, I will be ready to install new parts. As a snow bird, my machine sits idle for 6 months and I think things tend to dry out. Wonderful experience in ordering and video watching.

dishwasher does not drain

  • Customer: tom from bend OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working

Leaking

  • Customer: Valerie from Bedford TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
When I first noticed my unit leaking I noted that the leak was dripping right in the middle. So, I went straight to this web site with my model number and the 1st part I saw was for a Gasket Insert which is a small piece that completes the sea. I received that part in 2 day and did the repair and I still had leakage. I went back on the web site and looked further and came across info for the Corner Tub Baffles. I did not even know there were there. I removed mine and it was very obvious that the original Baffles were very worn and wrapped. In addition, the unit was quite filthy. I ordered the two replacement baffles. The parts arrived in two days, did the minor repair and now I have no leaks.

wheels of dishwasher (upper drawer) cracked off

  • Customer: JASON from GAITHERSBURG MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The PartSelect video told me to take the end caps of the track and simply snap the old wheels off. It was easy. I popped the new wheels on, put the rack back on, and reattached the end caps. I was surprised by how simple it was to repair a major kitchen appliance.

No water fill to dishwasher.

  • Customer: Lewellyn from Clarkston WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced the water-fill solenoid valve.

leaking drain valve shaft seal

  • Customer: Jim from Commerce TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
used the repair info from your website, many thanks! now I know where to come next time.

Broken lower wheel ion lower dishwasher rack

  • Customer: carole from Libertyville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Upper basket roller broken

  • Customer: Guntis from Sugar Grove IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the on-line video. It was great and made the replacement job easy. Without the video, I probably would have broken the plastic end caps while trying to take them off. I highly recommend watching any available repair videos.

Small leak at the bottom of dishwasher

  • Customer: Harry from Bayside NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

Rollers wore out

  • Customer: Joe from Langhorne PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video instructions..I was concerned that the end pieces would be a problem, so I purchased replacements also, but they came off with no problem - thanks to the video.They only cost about $2.50, so I will keep them in stock in case I need them at a later date.Without the video, it probably would have driven me nuts trying to figure out how to remove the end pieces, but when you see it done, it was simple.....Thanks Loads.

Leaking Dishwasher

  • Customer: Eugene from Port Saint Lucie FL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replacing the two corner baffles was the third attempt to stopping the leak. I first replaced the door seal without removing the inner door and the leak did not stop. Then I removed the inner door, reinstalled the door along the bottom and added the small seal required at the lower center portion which is separate than the longer door seal. Still leaked! Then I replaced the corner baffles and alas., the leak stopped. I would recommend that all seals be replaced at the same time. Total cost about $40.00 and can easily be done in one hour or less. I ordered the parts And they arrived remarkably in les than 24 House with regular delivery. Very pleased with Parts Select instructions and service!

Roller axles worn down

  • Customer: Dean from Mountain Home AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed rack by twisting and pulling off the plastic ends of the upper roller tracks. Removed old wheels from track and discarded. Removed old wheel assemblies from rack with fingernail. Replaced wheel assemblies on rack with the new ones. Alligned rack with tracks and pushed back into the dishwasher. Replaced plastic track ends with opposite action required for removal. Job completed.

Pump was leaking from the shaft seal

  • Customer: Anthony from Mechanicville NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.
All Instructions for the HDA2000G02WW
616-630 of 648