Models > HDA2000G02WW > Instructions

HDA2000G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000G02WW
511-525 of 648
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Hard to get end caps off -broke them

  • Customer: Linda from Tucson AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My dishwasher used this part # as a substitute for the original part, which i guess is no longer made. After reading the other customers' comments,I thought people were describing two very different experiences with the installation -- some just "popped the cap off the end," or "couldn't be easier." Others had so much difficulty getting the cap off that they broke the cap. I think people must be dealing with totally different kinds of plastic caps. When I started on mine, I couldn't find a way to just "pop" the cap off. It was made so that some small flexible stems or prongs that slid in when installed could not be slid back out. I used a pliers to twist, poke, tilt, bend, whatever I could do to get the plastic cap off the end. That wasn't working, so I tried to bend rims the metal track open, but found the metal was too thick or strong for me to bend it. So I had to twist and force the cap, and the piece that kept the cap on broke off. On one side of the rack it was broken so badly that it couldn't be put back on--kept falling off. Had to try to crimp the rims of the track inward to keep the cap on. It's very loose but it has stayed in for the most part. The cap on the other side cracked enough to get it out without completely breaking off a piece. It went back in better than the first side. Pretty frustrating! I suspect because I don't have the original part with replacement caps to slide in. ?????

water leaking on floor under dishwasher

  • Customer: Thomas E from Lexington SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one

Water would not fill.

  • Customer: Carlon from McRae AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Wow, could not have been easier. The suggested repair stated that the water inlet valve was the problem 93% of the time. And, it was spot on. It was the exact same replacement part. And, once installed, it worked like a charm. I have bookmarked this website, and will use it for all future appliance repair. I simply could not be more pleased. It was a breeze. Thanks,

Inside dishwasher door broke at door hinge.

  • Customer: Jeff from Rancho Cucamonga CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the existing inner door by removing screws along the edge of the inside door. Had trouble removing the door latch but after lifting it on one side of the plastic door fitting, it eventually lifted out. I also had some trouble getting the spring loaded soap door back into the replacement inner door. After playing with it for awhile I realized that the soap door should be in the open position when putting the spring latch back on. The soap door won't close until you get the entire inner door mounted and back on. I also want to note the the inside vent in the upper part of the inner door needs to be removed from the old inner door and installed in the new one. I missed that at first and it allowed condensation to get inside the door which caused the dishwashers alarm to go off during the dry cycle. One last note that I initially decided not to replace the existing sound proofing material in the new door based on advice from a website that stated that I wouldn't notice the sound difference. That was definitely untrue. I had to disassemble the door, replace the sound proofing and then it sounded fine. Overall it was a little difficult to figure out but considering how inexpensive the replacement door was compared with a having a service repairman come out, it was worth the trouble.

Our old racks were getting rusty and breaking off.

  • Customer: Timothy from Loma CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We did not want to spend money for a new dishwasher when the motor is doing just fine. So we went to our local Sears store and were told it would be $200.00 plus tax and it would be 7-10 days for shipping. So we went to partselect.com and ordered an upper and lower dishrack. It was here in 2 days and we paid about $175.00. They were really easy to replace and are working just fine.

Leaking

  • Customer: JESS from MORRIS IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the easy to follow instructions. Disconnected water, power, drain hose.. Pulled out unit. Tilted to back, used nut driver to disconnect motor brace, loosened hose clamps. Pulled pump/motor off. Unscrewed off defective part. Cleaned area of debris to reassemble the part ordered. Reconnect everything, reinstalled dishwasher. Turned on unit. No leaks! Dishwasher works great.

The dish washer was leaking around the bottom of the door.

  • Customer: Charles from Wade NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the old corner tub baffle's and replaced them with the new one's and that took care of the problem. I used a putty knife to remove the old one's and put some new adhesive on and put the new ones in place and let them set up for two days to let them really set up and they work really good no leaks.

Water pooling at bottom of dishwasher

  • Customer: Christel from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the sump cover and it was disgusting! This was the first thing I did to trouble shoot. I tried cleaning the cover but it was just too dirty. I ordered a new part and now I don't have any more water pooling at the bottom. I unscrewed the cover and then screwed on the new one. It did not come with screws so keep your original screws.

Valve was leaking. This is the second one that has leaked.

  • Customer: BILLY from SAN LUIS CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Remove front shields on bottom of dishwasher. Shut off dishwasher and electricity. Unplug electric connection. Unscrew brace holder screws on front. Remove clamped on hose at back of valve. Unscrew valve from copper water pipe. Screw on new valve to copper water pipe. Put on clamped hose. Screw on bracket. Plug in electric connection.

Plastic Slide end cap Broke and let the upper rack come out

  • Customer: Cynthia E. from Metropolis IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Put rack in place and snapped new one in.

Lower rear rack wheels

  • Customer: Judith W. from Topeka KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Quick and easy...a 7 yr old could have done it.

Leaking gasket

  • Customer: Patrick from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We removed old gasket, cleaned surfaces and installed new gasket.

Detergent cup cover could not be locked closed prior to washing the dishes.

  • Customer: Harry from Croghan NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.

Motor was making a grinding noise

  • Customer: John from Jacobus PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Turn off the power at the breaker panel. Turn off the water supply that goes to the dishwasher. Remove the front lower panel to gain access to disconnect the water line and electric. Now remove the two screws that connect the dishwasher to the countertop. You should be free to slide the dishwasher from under the countertop far enough to remove the drain hose. Slide the dishwasher out all the way and lay on the floor door down. Loosen the two clamps that hold the motor up. Remove the motor bracket, (should only be one screw. Disconnect the wires from the motor. Now just pull the motor down and out. Repeat the process to install the new motor. I took several pictures before I started removing anything. The instruction that comes with the kit is very good. Their will be parts in the kit that will not be used. Not to worry!

rollers on top rack broken

  • Customer: joseph from Coventry RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I popped out the stoppers at the end of the gliders. removed broken rollers and slid on new rollers.re-installed stoppers, tested all functions. tested good
All Instructions for the HDA2000G02WW
511-525 of 648