Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HDA2000G00WW > Instructions

HDA2000G00WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000G00WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000G00WW
76-90 of 649
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Motor was jammed, just heard a humm from unit.

  • Customer: Brook from Madison, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 7 of 8 people found this instruction helpful
First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

dishwasher filled base with clean water when not in use

  • Customer: Harvey from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 7 of 9 people found this instruction helpful
The repair was really easy. I ordered the part needed after looking at this website. I figured out the problem by looking into the forums. I ordered the part. It came within several days. I got home from work and after dinner pulled the dishwasher from under the kitchen counter. It was easy to do. I flipped the dishwasher on its side. Then removed the old part. It had a water inlet that required a fitting to be loosened with a wrench. It also had a flexible water fill that was attached with a cable clamp. (Remember to turn your water supply off first!) The wiring was disconnected by a simple harness. Four bolts had to be removed to pull the part off of the dishwasher body.

Installation was the reverse of this process. Have been using for a week now and the problem is corrected. Doing business with Parts Select is awesome. I know that over the last several years I have saved tons of money and learned that I can fix nearly any appliance by viewing this website.

Water Leak In Rubber Connector Pin Hole At Seam

  • Customer: Allan from Stony Point, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.

Rusted out racks

  • Customer: Everett (Jeff) from Altus, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Followed the instructions and it was easy. Made the washer seem brand new!...It is the best solutions for a small budget. We used CLR to wash out the washer workings and it really left a sparkle on the dishes... I am so glad you don't change the models so much that parts can't be exchanged when they wear...

Water would not drain.

  • Customer: Jay from North Liberty, IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 12 people found this instruction helpful
The washer ran through a full cycle, but the water didn't drain out. I pulled out the drain vent and checked for foreign objects. Also checked at the drain hose/disposal joint and there was no blockage. After removing the bottom panels I noticed the solenoid was shot. Cylinder was burnt up and stuck solid in the up position. I went online and found that a main cause of this can be from the timer causing the solenoid to over exert and burn out. I decided if I was going to order parts and dig into a repair I should replace both. For the timer it is just a matter of unscrewing the inner door panel and unplugging the old timer. Then inserting new one. Couple of things I ran into were the door is no longer heavy enough to stay down so I grabbed a waffle iron as a weight to hold it down. Also will need to unscrew the set screw on the Door lock latch's bottom side. Pay close attention to how it was together helps. For the solenoid I removed the main screws holding the unit in place as well as the c-clip holding the plastic arm. Undo the spring and plug and the whole unit comes out. Reverse these steps with the new solenoid to install.

rust

  • Customer: Oria from Scottsdale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
Just took the old rusty rack out and put the new one in its place.

Lower dishrack getting rusty in spots

  • Customer: Catherine from South Hadley, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.

Stinky Dishwasher

  • Customer: Jeremy from Hailey, ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 7 people found this instruction helpful
I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Dishwasher wouldn't drain

  • Customer: Jeffery from Sparks, NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Roller front shafts broken

  • Customer: EUGENE C from WICHITA, KS
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Rack fits perfectly. The problem was removing the old Rail End Caps and then re-installing them. The are plastic and nealy impossible to remove. Finally after much coaxing was able to get them out. Howver, putting them back on was impossible. The long guide that nests inside the Rail could not be made to slide in so the latching hook could go into the rectangular hole. The hook prevented the long guide part from staying in the Rail on the upper end. Tried bending the long guide and it got it to nearly work, but the guide broke. It did not come completely off so left on and just pushed up after hook was put in hole. Doesn't seem to hinder operation. There was a plastic "tower" piece that must be for some other model. The Rack has a place for the Tower, but it wasn't part of the original Rack.

Leaking water at the solenoid valve stem

  • Customer: Gordon from Stone Mountain, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

2 rollers and end caps were broken were broken

  • Customer: Robert from Old Lyme, CT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT

  • Customer: Raymond from ansonia, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

One of my top rack rollers had broken and the rack could not hold any weight

  • Customer: Louis from Fairfield, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 11 people found this instruction helpful
I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

Broken Roller

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.
All Instructions for the HDA2000G00WW
76-90 of 649