Models > HDA2000G00WW > Instructions

HDA2000G00WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000G00WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000G00WW
61-75 of 615
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher leaking from pump shaft seal

  • Customer: John from Brentwood CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 10 people found this instruction helpful
first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to the motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

Broken Inlet valve

  • Customer: ROBERT from ALBANY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 8 of 11 people found this instruction helpful
Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!

The seal for the drain valve was leaking.

  • Customer: mary from orlando FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
I removed the front bottom panels to give me access to the Solenoid area. I did not take out the dishwasher from the cabinetry. I removed the screws holding the solenoid assembly and the C clip holding the hand fan shaped white nylon thing onto the valve shaft. I slipped these to the side. Then I cut through and removed the push on nut with a wire snipper plier. Then I used a knife blade tip to pick out the black seal. I then slipped the new seal onto the shaft, being careful that the flat side was outward, and slid it down the shaft and , with my fingernail, pushed it completely flush into position. The biggest challenge was the push on nut. It does not push on easily and must have the lips pointed outward. It required the use of a 3/8" diamater tube slipped over the shaft to tap the nut down the shaft. This caused the shaft to push into the pump housing, which caused the valve to bind. So I used a vice grip to pull out on and hold the shaft while I tapped the push on nut with a flat head screwdriver. Then I just reversed the solenoid assembly removal. But , when I ran the dishwasher, it no longer leaked.

A house mouse tore through the rubber housing

  • Customer: Alan from Rossville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
I pulled the dishwasher out from under the counter. Loosened the collar holding the sump housing to the pump motor. Unscrewed the cover inside the base of dishwasher to release the collection opening of the sump. It's very flexible so I pulled it out by hand. Put the new one in and screwed everything back down. Pushed the dishwasher back under the counter. Simple Simple Simple.

water inlet valve leaked

  • Customer: William from Westminster MA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 7 of 9 people found this instruction helpful
I cut the water off to the DW, unscrewed the water connection to the inlet valve, unplugged the electric connection, disconnected the black rubber line from the valve to the washer, removed the 2 screws holding the valve in place. Put the new valve on by doing the above backwards. I also used white thread tape on any connections that needed it.

WATER LEAK IN RUBBER CONNECTOR PIN HOLE AT SEAM

  • Customer: Allan from Stony Point NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling Housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip., rescrewed in the new rubber connector. (
HINT- used petrolem vasaline on the rubber connector base for a water tight fit) . reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. turned water back on.

All worked at well.

Motor was jammed, just heard a humm from unit.

  • Customer: Brook from Madison WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

After twelve years the prongs on the top rack began to break and rust.

  • Customer: Jim from Wichita Falls TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
I ordered a replacement from partselect.com and received it in just three days. The only difficult part was deciding how to remove the white plastic end caps on the sliding rails. Finally, I took a small screwdrive and pried out the crimps in the metal, pulled the old caps out, inserted the new ones, and squeezed the metal together again using needle-nosed pliers. Nothing to it!
Note: The configuration of the new rack isn't exactly like the original (size and placement of the prongs differ somewhat) but it fits perfectly and works great.

attaching overflow micro switch to new plate

  • Customer: GEORGE from CHAMBERSBURG PA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 7 of 9 people found this instruction helpful
Once i had the dishwasher removed everything went as the instructions indicated except for the overflow switch.I removed the switch from the old bracket which is not required,just install the switch assy. to the new bracket and proceed as instructed. the total repair shouldn't take more than 1 hour if you don't make the mistake i made.I AM VERY SATISFIED WITH PRODUCT.
I HAD NEXT DAY DELIVERY AT REGULAR POSTAGE CHARGE.

One of my top rack rollers had broken and the rack could not hold any weight

  • Customer: Louis from Fairfield CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

Water stays in the bottom because the solenoid burned out.

  • Customer: Guorong from Novi MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts.
A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.

Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT

  • Customer: Raymond from ansonia CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Roller front shafts broken

  • Customer: EUGENE C from WICHITA KS
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Rack fits perfectly. The problem was removing the old Rail End Caps and then re-installing them. The are plastic and nealy impossible to remove. Finally after much coaxing was able to get them out. Howver, putting them back on was impossible. The long guide that nests inside the Rail could not be made to slide in so the latching hook could go into the rectangular hole. The hook prevented the long guide part from staying in the Rail on the upper end. Tried bending the long guide and it got it to nearly work, but the guide broke. It did not come completely off so left on and just pushed up after hook was put in hole. Doesn't seem to hinder operation. There was a plastic "tower" piece that must be for some other model. The Rack has a place for the Tower, but it wasn't part of the original Rack.

Old roller wheels were starting to stick due to cracking

  • Customer: Jeffrey from Springfield VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.

Broken Roller

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.
All Instructions for the HDA2000G00WW
61-75 of 615