Models > HDA2000G00WW > Instructions

HDA2000G00WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA2000G00WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA2000G00WW
601-615 of 646
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wash water not entering

  • Customer: James from BOULDER CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
took the front covers off, used om meter as suggested after disconnecting the wire plug. discovered infinity, so as suggested, determined the valve defective. Ordered over the new valve from this company. After it arrived, took the old valve off by removing it from the bracket. Used the pliers to take the hose off, then unscrewed the supply hose by usung the adjustable wrench. Took the old valve to my shop vise to hold it firmly, then unscrewed the fitting, wrapped the tape suggested and installed it on the new valve. Took it back to the dishwasher, screwed the supply hose on, slipped the hose on and the clamp, turned on the water to check for leaks. Found non, so installed the valve on the frame, turned on the power and checked for filling. Itfilled fine and operated like it was supposed to. Put the front covers back on, and enjoyed praise from wife!!!

Leaking water

  • Customer: Chuck from Austin TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Most difficult part of repair was getting dishwasher out and in under the cabinet. Especially, feeding the copper water line from under the sink and then back while trying to align the connection. Installing the part itself was easy with good instruction for taking it off and reinstalling. However, since the motor had been upgraded, it required new connections. The connections were provided for this, but no instructions for the electrical connections.

This is a "Kit of 4 rollers" for $10

  • Customer: James from Millsboro DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
If you put this in your cart, the invoice will come out with a unit cost of $10, and a total coat of $40 for 4 plastic rollers. Fortunately, the rack I ordered had the rollers included, so I deleted this item. Putting in the rack itself was a piece of cake.

Water leak from gate (diverter) valve

  • Customer: Robert from Oak Island NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Read Joseph from Livermore, CA for good instructions. I took a camera phone photo for reference before I started. Should have taken another photo half way thru. Probably put the push-on-nut on backwards as it didn't 'lock' in - had too much play in the shaft, would have leaked. Impossible to get nut back off in good shape. I put original mangled push-on-nut on also - it added enough tension to eliminate play in the shaft. No leak..but lucky. Go ahead, you can do this repair for under $20.

water inlet valve stuck open (frozen??)

  • Customer: Richard from Bay Village OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!

Incomplete cleaning / standing water / drain failure

  • Customer: John from mars PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
There is sufficient clearance to remove the motor and pump from under the dishwasher after removal of the front lower panels. This avoids the inconvenience of moving the dishwasher. Some ouch work required to remove some of the fittings as sight lines are obstructed - use a mirror to help. Installation is easier as all but one of the hose and pump clamps can be installed with the screw heads accessible from the front. Only installation issue was that the mounting holes on the pump body for the ground wires and the support piece had been drilled but no screw threads had been cut. Two minutes work with a tap solved the problem. One suggestion is to run a couple of loads before replacing the front cover to check for leaks. I did find one after the second load.

Replaced the broken plastic insert in the wheel

  • Customer: Daniel from Odenton MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Followed the instructions on the website video. Piece of cake! No tools were required. Insert the plastic insert into the wheel ensuring the right side faces the rack. Snap onto the rack once done.

Dishwasher racks were replaced in the first order.

  • Customer: Philip from Parkland FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
When I received the first order the lower rack didn't fit because it wasn't wide enough. Your people replaced the rack and now all works in good fashion. Thx, Phil

Lower dishrack rusted

  • Customer: susanne from Moorpark CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Instructions for repairs. Remove old rack from dishwasher. Stop, have a beer. Open packing box. Remove new dishwasher rack from box. Rest. Have another beer. Slidey old thingamajig rack ouy from dithwather. Shove into packing box. Figure out where you put the new rack. Pick up new rack, put new rack on countertop. Hav anoder beer. Put nw wreck in dithwather. Take bx & bee botluls to trash. Take nap. :>) S.

leaking drain valve. note i took the disherwasher out about six months to remodel the kitchen it wasn't leaking when i took it out , but being out so long with out water in it, it started to leak when i put it back in !! !!

  • Customer: ronald from pompano beach FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
i replaced the drain seal without removing the dishwasher as far as the push on nut i had to use a round punch to open the tabs a little.. i also used Vaseline to hold the c clip in place to snap it in with a screwdriver

rollers broke

  • Customer: James from Simpsonville SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed new ones as per instruction

Dishwasher was leaking out the left front

  • Customer: Anita from Boon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the corner baffles and installed them in the corners in just minutes. Repair company quoted me about $100 if they had the parts on the truck. If they had to come back it would be another service call. Did the repairs my self for $24 with shipping charges. Happy Customer

Upper dishrack broken tines

  • Customer: Richard from Pecos NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After receiving the third shipment of a new basket without a broken center water diversion cone, removing the rail keepers, slipping the new basket onto the rails and replacing the keepers was easy. What wasn't easy was persuading the shipping department to secure the cone within the shipping container -- which never happened, since the third and last shipment contained an unbroken cone only by chance.

roller broke

  • Customer: Sam from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
follow your video instruction. very simple.

The dishwasher was not draining

  • Customer: Marcus from Argyle TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The machine had been running sluggish for a while. Replaced the pump awhile back, but it still wasn't draining good. Then it quit draining. The solenoid is mounted on the pump, two screws and a clip on the valve door shaft come off. The new one is easy to put on. Caution: many of these appliance people say that timers are often needlessly replaced, but when I looked at the old solenoid, it looked like a meltdown had occurred. It was not worn out, it had overheated. Checked out timer and found cause. The gear on the motor shaft was partially stripped, causing drain valve to stay open too long. New timer, solenoid, pump-ten years old and never ran this good.
All Instructions for the HDA2000G00WW
601-615 of 646