HDA2000F01WH Hotpoint Dishwasher - Instructions

within 5 minutes.Great site for information and parts

The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in the 4 years we have owned the house.

I thought to myself, this is going to be easy, but I hit a couple bumps getting the end caps off. I just watched the video and it was great and helped me be sucessful. The only thing that would have helped was instructions on how to put the end caps back on! david

Removed the tray from its rails. Removed axle clips fro tray and replaced with new axles. Put tray back in rails and I was done. Works like

To remove the old upper rack, I needed to use a screw driver to snap out the plastic end stops. That took a little time, because my dishwasher is located in a corner of my counter/cabinets, making the stop on the right very difficult to get to. Once that was done, I just slid the old rack out, the new rack in and replaced the stoppers. I was very impressed with your service and received my order in less time than stated on my order form. Will definitely use you again and recommend you to others!

The upper rack fit, but the rack differed from the original to the extent that glasses that normally could be washed on the upper rack no longer fit, and the inverted upper rack "funnel" is further from the water stream nozzle reducing the effectiveness of cleaning on the upper rack. The rack rests significantly higher in the machine than the original.

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

Ordered parts from Parts Select, and replaced lower roller wheels. The diagrams/ drawings were key in ordering the correct replacement parts - thanks

In the video, they must have been removing new parts from a new machine. 7 year old parts do not come off so easily. You may need a screw driver (I used a plain old dinner knife) to pry up the prong. (Parts went flying as they broke off for good!) I had to use a wrench to get the roller off. BUT, the new part slipped on like "greased lightening." Sooooooo, watch the video, follow their step by step instructions, but be prepared with a tool or 2 since the only reason you are doing this is because it is OLD!!!

Pop the new wheels on. The rear wheels are thinner than the front wheels so rack slides in smoothly

After examining the lower baffles, it was evident that their grooves were bent out of shape and warn. They were simple to pop out, I cleaned the area and popped in the new baffles. Unfortunately, the leak still happened. Upon further examination, the corners of the gaskets where they rubbed against the baffles also looked worn. So I ordered a replacement gasket and gasket insert and just installed them. Problem solved. The instructional videos were exceptionally clear. I'm not particularly handy. If I had not seen the videos online before ordering the parts, I would have called a repair service and spent $150+ more.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

There is no repair easier than this! Simply remove the decayed gaskets and replace with new. No tools, no glue, no nothin'.

Just watch the video and you will be fine. The only thing I would suggest is buying both your rack slide end caps because with the age of my machine they were brittle and cracked/broke where they were supposed to only bend. Spend the extra $.64 and you will be glad you did.

well, having read the previous customers installation comments, i was prepared to have issues with the little clips that go in the tracks for the top rack. however, it was much easier than anticipated. all you have to do is bend the tab out so the clip will easily slide into the track and clip into place. no twisting or funny angles needed. for removing them, just use a flathead screwdriver to get in the track and bend the tab out so they easily slide out. super simple.