HDA1200G00WW Hotpoint Dishwasher - Instructions

Actually, the problem started with a Timer Motor failure, and that let the dishwasher run for 4 hours (doh!). Immediately, I tested and ordered the timer, which unfortunately didn't come as just a motor, it came as an assembly. I installed it, and the dishwasher ran the cycle just fine.

Except it didn't drain.

After poking around, I noticed the drain solenoid had apparently been overworked; the timer must have failed on DRAIN. The solenoid was severely overheated, and thankfully didn't cause a fire, but it was somewhat melted. Replaced the solenoid, and all is well, especially when my wife was eyeballing a $1000 Bosch!

I ordered parts before opening. My theory was to have the parts so that the dishwasher was not apart for longer than necessary, in the hope of avoiding the wrath of momma bear who just wants a new one... Once I opened up the door I realized the spring for the main lever arm had broken its mount. I drilled a new hole and reattached the spring. I did not need any parts. However, the original parts corresponding to the three parts I ordered were all beat up and brittle, so I was happy to replace anyway. I did not even explain, she is happy the cup looks new and is happy with the dishwasher. It even says Cascade on it, almost like an upgrade :). If your cup does not latch I would order the three parts I did and also order the lever spring. It was very corroded after 30 years, so I would have replaced if I purchased it. Next time.. :)

Unscrewed old spray arm by hand. Screwed new one on by hand. Two minute job. New arm and tower were better than old one. Piece of cake at a very low price.

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days later i had the parts, and the next day I had a fully functioning leak free dishwasher.

This is a great website. I ordered my part on Wednesday night and it arrived Saturday morning without paying any extra for shipping. Plus since I am a female, this website enabled me to easily and affordably make the repair myself without having to worry about a repair man trying to take advantage of someone that they think they can.

I first made sure that there was nothing stuck in the drain area inside of the dishwasher. That meant I had to bail out all the standing water and then unscrew the mesh cover from the bottom. Since there was nothing in there I ordered a new solenoid.

First I unplugged the dishwasher. Then I removed the screws with a screwdriver that held the bottom cover on the dishwasher. Once I could see the installed solenoid, I put together the pieces of the replacement solenoid that I bought so I was sure to install the new one correctly. That did not require any tools. Then I unscrewed the two screws that held the solenoid in place and removed the little metal ring from the shaft which was the last piece holding it in place. Getting that ring off was tricky. I ended up using a pair of tweezers to pull it off. After that I put the new part on and screwed it in with the two screws provided. The little metal ring went on much easier than the old one came off. I screwed the bottom cover back on and voila! my dishwasher was fixed.

Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to the motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rags and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.

Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!

Followed the instructions and it was easy. Made the washer seem brand new!...It is the best solutions for a small budget. We used CLR to wash out the washer workings and it really left a sparkle on the dishes... I am so glad you don't change the models so much that parts can't be exchanged when they wear...

I made this replacement more dificult because I removed the old motor/pump earlier. Should have done it at the time I installed the new unit to be sure all hoses where installed correctly. I hooked the drain hose to the wrong port and when I started the dishwasher I found my error. Once I corrected the problem and started it again - the wash and drain cycles were perfect and there were no leaks.

I ordered a replacement from partselect.com and received it in just three days. The only difficult part was deciding how to remove the white plastic end caps on the sliding rails. Finally, I took a small screwdrive and pried out the crimps in the metal, pulled the old caps out, inserted the new ones, and squeezed the metal together again using needle-nosed pliers. Nothing to it!
Note: The configuration of the new rack isn't exactly like the original (size and placement of the prongs differ somewhat) but it fits perfectly and works great.