HDA1100N10WH Hotpoint Dishwasher - Instructions

I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.

Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.

Removed bottom panel unplugged wires removed two screws removed it then replaced it

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.

The part I received was not an exact fit replacement even though it was specified for the dishwasher model I entered. The part had to be modified to allow it spin into place. In addition a portion of the tab on the stud had to be cut off to allow the stud to go in.

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

After examining the lower baffles, it was evident that their grooves were bent out of shape and warn. They were simple to pop out, I cleaned the area and popped in the new baffles. Unfortunately, the leak still happened. Upon further examination, the corners of the gaskets where they rubbed against the baffles also looked worn. So I ordered a replacement gasket and gasket insert and just installed them. Problem solved. The instructional videos were exceptionally clear. I'm not particularly handy. If I had not seen the videos online before ordering the parts, I would have called a repair service and spent $150+ more.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

There is no repair easier than this! Simply remove the decayed gaskets and replace with new. No tools, no glue, no nothin'.

Replaced the tray with a new one. Would have been no problem at all, if I had realized how the track end clip was supposed to go. I thought the release had to be pushed toward the lock, but it needs to be pushed away from it. This sounds confusing, but when you look at it, it may be more clear to you.

go to google..replace ge dishwasher rack.. very clear way to pry tab with a quarter and rotate end cap.. remove/replace rack reverse install end cap

open packages of baffles, installed per video, done, no leak!