Models > HDA1100N10WH

HDA1100N10WH Hotpoint Dishwasher - Overview

Get Parts and Repair Help for HDA1100N10WH

If you know the dishwasher repair part you need, you can browse the list of all parts on the HDA1100N10WH, or you can search by name or part description. You can also find your part by where it is located on the HDA1100N10WH by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for HDA1100N10WH parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the HDA1100N10WH [Viewing 3 of 3]

$1.46

Single Lower Rack Wheel

This wheel is located on the lower rack. It is sold individually and does NOT come with the attaching axle.

$0.69

RACK SLIDE END CAP

This part attaches to the rails, for the upper rack, to prevent the dishrack from sliding all the way out.

$10.00

Lower Rear Rack Wheel and Axle Kit

This kit contains one wheel and one axle. It is designed for the rear lower dishrack. Sold individually. Order quantity needed.

$7.04

Corner Tub Baffle - Lower Left

The left and right side baffles should be installed/replaced at the same time. Right side baffle is sold separately.

$7.02

Corner Tub Baffle - Lower Right

This baffle fits the lower right hand corner of some dishwashers. It is black and has a matching left hand lower corner baffle. It is recommended that you replace and install both ...

$87.32

Lower Dishrack with Wheels

$13.02

Silverware Basket

This silverware basket is gray.

$53.64

Door Gasket - White

This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.

$16.89

Drain Valve Shaft Seal

$2.79

Push On Nut

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower rack wheel was melted

  • Customer: Mark from Huntingdon Valley PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 461 of 462 people found this instruction helpful
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience. read more

The rear wheels were missing on the lower rack.

  • Customer: Teresa from Phenix City AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 458 of 460 people found this instruction helpful
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama. read more

Water leak from gate (diverter) valve shaft

  • Customer: Joseph from Livermore CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 83 of 91 people found this instruction helpful
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was... read more