HDA105Y-72WH Hotpoint Dishwasher - Instructions

Simply replaced both cables to allow door to open and operate as intended, without dropping unrestrained, which could possibly cause more serious damage to door and/or washer.

follow your video instruction. very simple.

When I first noticed my unit leaking I noted that the leak was dripping right in the middle. So, I went straight to this web site with my model number and the 1st part I saw was for a Gasket Insert which is a small piece that completes the sea. I received that part in 2 day and did the repair and I still had leakage. I went back on the web site and looked further and came across info for the Corner Tub Baffles. I did not even know there were there. I removed mine and it was very obvious that the original Baffles were very worn and wrapped. In addition, the unit was quite filthy. I ordered the two replacement baffles. The parts arrived in two days, did the minor repair and now I have no leaks.

The PartSelect video told me to take the end caps of the track and simply snap the old wheels off. It was easy. I popped the new wheels on, put the rack back on, and reattached the end caps. I was surprised by how simple it was to repair a major kitchen appliance.

order new gasket and it took us last them 15 min. and it was ready. I will start using it at least twice a month from now on. I would like to thank Part Select for getting the part that we need so fast and with helpful instructionf

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Watched the on-line video. It was great and made the replacement job easy. Without the video, I probably would have broken the plastic end caps while trying to take them off. I highly recommend watching any available repair videos.

Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.

I followed the video instructions..I was concerned that the end pieces would be a problem, so I purchased replacements also, but they came off with no problem - thanks to the video.They only cost about $2.50, so I will keep them in stock in case I need them at a later date.Without the video, it probably would have driven me nuts trying to figure out how to remove the end pieces, but when you see it done, it was simple.....Thanks Loads.

Remove lower covers (2) Remove broken cable. Replace with two new ones. Hook eyelet end to one side then springs then hook other eyelet to other side pull springs tight and hook to cable. Keep both sides tight doing so.

Removed rack by twisting and pulling off the plastic ends of the upper roller tracks. Removed old wheels from track and discarded. Removed old wheel assemblies from rack with fingernail. Replaced wheel assemblies on rack with the new ones. Alligned rack with tracks and pushed back into the dishwasher. Replaced plastic track ends with opposite action required for removal. Job completed.

Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.

I watched the YouTube video about removing the end tabs on the upper rack then simply removed them with a flat head screw driver. Then, after replacing the rack, I re-inserted the tabs using the screw driver. as shown in the video. There's really nothing to it after watching the video, which is about 2 minutes long.

First open the door and look at the corner tub baffles. They are in the bottom corners where the door seals with the tub and they look alike. Remove and replace one at a time making note of the orientation. Make sure they are firmly seated in the bottom and close the door and enjoy.

Dishes were not being cleaned, so the first thing I did was take the float cover off and cleaned the soap gunk off (it was getting stuck open). That solved about 50%. I could tell that the spray arm was gunked (and partially clogged) so I replaced it with this one. A pipe wrench got around the base and I torqued it loose and off, cleaned the inside with a paper towel, and I put the new one on hand tight. Dishwasher works like new again.