HDA1000N10WH Hotpoint Dishwasher - Instructions

When I received the first order the lower rack didn't fit because it wasn't wide enough. Your people replaced the rack and now all works in good fashion. Thx, phil

Instructions for repairs. Remove old rack from dishwasher. Stop, have a beer. Open packing box. Remove new dishwasher rack from box. Rest. Have another beer. Slidey old thingamajig rack ouy from dithwather. Shove into packing box. Figure out where you put the new rack. Pick up new rack, put new rack on countertop. Hav anoder beer. Put nw wreck in dithwather. Take bx & bee botluls to trash. Take nap. :>) S.

Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.

I ordered the corner baffles and installed them in the corners in just minutes. Repair company quoted me about $100 if they had the parts on the truck. If they had to come back it would be another service call. Did the repairs my self for $24 with shipping charges. Happy Customer

My machine stopped leaking after I simply massaged the door gasket and cleaned the baffles. I did order the necessary parts, they arrived in a very timely manner and the process was painless. After watching the video for both the door gasket and the tub baffles, when my machine decides to leak again, I will be ready to install new parts. As a snow bird, my machine sits idle for 6 months and I think things tend to dry out. Wonderful experience in ordering and video watching.

When I first noticed my unit leaking I noted that the leak was dripping right in the middle. So, I went straight to this web site with my model number and the 1st part I saw was for a Gasket Insert which is a small piece that completes the sea. I received that part in 2 day and did the repair and I still had leakage. I went back on the web site and looked further and came across info for the Corner Tub Baffles. I did not even know there were there. I removed mine and it was very obvious that the original Baffles were very worn and wrapped. In addition, the unit was quite filthy. I ordered the two replacement baffles. The parts arrived in two days, did the minor repair and now I have no leaks.

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Attached is a link to a great youtube video, that shows the exact steps to take to do this job. I just follow the instructions and the repair was flawless.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

Repair was really easy just like the repair video, but you have to lay on the floor. Unfortunately, the problem wasn't the solenoid, but the pump/motor assembly. Be sure to check the solenoid operation before replacing (making sure it is cycling). It might be the pump/motor assembly. Good luck!

This is a somewhat difficult task in that the dishwasher had to be pulled out of the cabinet which required the water inlet hose to be removed (and water to the hose to be shut off). Once the dishwasher was free of the cabinet it had to be flipped over to reach the water inlet valve. Once the valve was replaced go in reverse to reinstall the dishwasher. Worked fine after I got everything installed; no leaks.

Took pliers and removed old end caps, replaced rack/roller slides then put on new end caps. Was just that fast and easy. No problems. Doing it myself saved me a bundle of money. Thanks Partselect...just hope I won't need you for awhile. B. Williams

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

knew the cause of problem ordered parts prompt delivery 16 yr grandson did the repair with little or no assistance

Removed old dishrack. Inserted new dishrack.