Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HDA1000K01 > Instructions

HDA1000K01 Hotpoint Dishwasher - Instructions

All installation instructions for HDA1000K01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA1000K01
1-15 of 583
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The rollers on the upper rack broke

  • Customer: Carl from Fairfield, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 496 of 502 people found this instruction helpful
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.

Wheel broken off bottom rack

  • Customer: Julie from Maumee, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 474 of 475 people found this instruction helpful
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!

Lower rack wheel was melted

  • Customer: Mark from Huntingdon Valley, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 474 of 480 people found this instruction helpful
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

The rear wheels were missing on the lower rack.

  • Customer: Teresa from Phenix City, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 461 of 465 people found this instruction helpful
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

Broken upper rack roller, rack kept falling off the track

  • Customer: Doug from Columbus, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 381 of 384 people found this instruction helpful
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.

Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.

Rollers fell off lower rack of dishwasher.

  • Customer: Lloyd from The Villages, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 364 of 365 people found this instruction helpful
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.

The stud assembly in the middle of each wheel no longer stayed inside the wheel.

  • Customer: Wendy Baldwin from Stowe, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 366 of 372 people found this instruction helpful
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.

Rack falling off of upper slides

  • Customer: Eric from Centreville, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 202 of 270 people found this instruction helpful
1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away

wheel replacement

  • Customer: michael from perry hall, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 219 of 409 people found this instruction helpful
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs

Water leak from gate (diverter) valve shaft

  • Customer: Joseph from Livermore, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 116 of 125 people found this instruction helpful
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect.

Dishwasher leaking at door seal.

  • Customer: Kenneth from Goleta, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 73 of 79 people found this instruction helpful
Removed door seal and corner baffles by hand (no tools required). Replaced same parts with minor tweaking to get proper alignment of new seal. Strongly recommended: remove dishwasher trays in order to get head and shoulders inside for proper view of seal placement.

wheels were worn out and kept falling off

  • Customer: JOHN from PURCELLVILLE, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 67 of 69 people found this instruction helpful
popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.

Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)

  • Customer: Don from Mount Vernon, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 60 of 65 people found this instruction helpful
1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to gain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.

Install new valve by reversing the procedure.

front twoo rack rollers broken ,bottom rack roller broken

  • Customer: Russell from Pueblo, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 74 of 136 people found this instruction helpful
for the top rollers you must remove thethe end cap. this was easy ,i placed a block of wood on the outside .placed the punch on the inside where the channel is pushed in to hold cap on. smacked it till it was pushed out far enough to remove end cap. new rollers simply snap on. very easy,

Dishwasher door became really heavy to operate

  • Customer: Karthik from Springfield, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 43 of 47 people found this instruction helpful
Note: This procedure assumes replacement of both eyelet cables. It is recommended that both eyelet cables be replaced at the same time.

1. Using a Philips' head screwdriver, remove the four screws holding the lower front panel (below dishwasher door).
2. Remove the faulty eyelet cable(s) hooked into the springs at one end and the door hinges at the other.
3. Take the new eyelet cables and hook them onto the door hinge on either side. Ensure a secure fit.
4. Guide the eyelet cable around the spinwheel on one side and insert the hooks of the springs into the eyelets.
5. Pull on the springs and insert their hooks into the eyelets of the other cable, ensuring a secure fit.
6. Test the door by opening and closing it a few times to ensure the spring has tension.
7. Replace the lower front panel cover removed in step 1 with its screws.
All Instructions for the HDA1000K01
1-15 of 583