Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HA3000

HA3000 Amana Washer - Overview

Get Parts and Repair Help for HA3000

If you know the washer repair part you need, you can browse the list of all parts on the HA3000, or you can search by name or part description. You can also find your part by where it is located on the HA3000 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for HA3000 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 8 hrs and your part ships today!
$24.77

Inlet Hose Kit

This hose is almost 5 feet long and now comes with the washers for proper installation. It is used to bring water into your washer for the cycles.

Order within the next 8 hrs and your part ships today!
$20.50

Brake Pad Kit

Included in this kit are three long shoulder bolts, three short boulder bolts, three brake pads, three short rubber grommets, & three long rubber grommets..

Order within the next 8 hrs and your part ships today!
$54.61

Flex Vane Agitator

This white agitator is used for belt driven washing machines.

Order within the next 8 hrs and your part ships today!

Drive Bell and Seal Kit

This washing machine drive bell and seal kit comes with a seal, a plug, a shoulder screw, a drive bell, and some grease.

$7.93

Screw

1/4-20

Order within the next 8 hrs and your part ships today!
$4.80

Washer

This washer is located between the brake and transmission drive pulley.

Order within the next 8 hrs and your part ships today!
$49.89

Brake Rotor Assembly

Order within the next 8 hrs and your part ships today!
$22.60

Siphon Break Kit

Included in this kit are the clamps for the drain hose.

Order within the next 8 hrs and your part ships today!
$5.63

Idler Pulley Lever

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Frayed V-belt

  • Customer: John from Milton, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 45 of 51 people found this instruction helpful
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bra... read more

Bearing went out causing lots of noise.

  • Customer: mike from hull, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 19 of 21 people found this instruction helpful
This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes t... read more

Machine stopped in spin cycle and smell of burnt plastic.

  • Customer: Tim from Cumming, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 14 of 16 people found this instruction helpful
Removed pump/motor assembly. Had a difficult time removing pump from motor. Was not aware that the shaft was not connected some way! After looking over the internet for help....I finally realized that the shaft was siezed in the pump. After much persuasion on my part....it broke loose... I did use some WD-40....but don't know if it....or my prying betwee... read more