GWRE6270H1WW General Electric Washer - Instructions

I took the two screws out that was holding the bracket and hose in place. I then pulled the hose out and then had a little bit of a hard time taking off the bracket (it was plastic and felt if I bent it to hard it would break) wiggling it down to the end of the hose. Re inserted the hose attached bracket, and I was done.
It would have cost me a lot more then $20.00 to have a repair man come in and fix it.
Love the service, delivered in two days.
Will use them again.

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

Replaced the button and was working in less than Fifteen Minutes.

Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.

Changing the belt didn't solve anything. We took the console apart and there is a Troubleshooting Guide folded up in there. It has a Code List and a sequence to follow to determine the trouble codes. While there was nothing wrong as far as coding, it did lead us to confirm the discharge pump WAS working, even though there was no water coming out. The discharge hose was plugged.

Couldn't get the agitator off by pulling up, then thought about it and got 2 carpenter claw hammers, inserted one on each side and puled up evenly on both and off she came. Sprayed the slots with WD Forty and popped the new on. THANKS saved us a lot of money!!!

The belt is very tight. Use a zip tie to old the belt on as you work it around the large pulley. Once it is on remove zip tie and turn the pulley enough times to line up the belt evenly then your done.

Inside the appliance is an instruction sheet that describes replacing the part and followed it mostly. To improve your instructions, pictures with the instructions are much more effective and easier to understand.

replaced circuit board and housing, I have never done this before, but at this time, with the way the Presdent and Congress is taking everthing away, you need to save every penny. So I talked replaced it myself..and saved about $200.00.

I just did a google search and found a video that shows to use a zip tie to hold the belt to the big pulley and simply turn the drum and the belt goes right on. Then cut the zip tie off and you are ready to go. Took all of 3 minutes to change the belt from start to finish.

With the instructions found online, this was a quick easy repair. I used youtube to have video to show the method. Used rope to pull up agitator, used wrench to loosen bolt and then put back together. Part was delivered really fast, I recommend Partselect.com for the parts you need!

Step one: Order the Belt and the $10.00 tool that fits on the motor sprocket to keep the belt from slipping off. Step 2: Lean the washer back at about a 45 degree angle, you may have to disconnect the water lines to achieve this. This puts the machine in a good position when you sit in front of it as you are installing the belt. Step 3: Install the tool over the motor sprocket leaving the grooves exposed. The belt fits in these grooves. Step 4: Slip the belt over the motor sprocket first and than the large sprocket wheel behind. This will take a little muscle as the belt is considerably smaller. After a couple of attempts at rotating the big sprocket the belt kept slipping off. I than took a plastic tie and strapped it around the belt and the big sprocket wheel, this kept the belt from slipping off as I rotated the wheel. Once the belt is on snip off the plastic tie and you are home free.

I was frantically trying to find a cheap washer to replace the one that "broke". Fortunately, my son's roommate is a maintenance technician. He diagnosed the problem immediately. I googled the issue, found the part, ordered it and received delivery of the part in 3 days. It took all of 5 minutes to replace the part and reassemble the washer. Now on to the 15 loads of laundry that have been stacking up!