Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GW397LXUB06

GW397LXUB06 Whirlpool Range - Overview

Get Parts and Repair Help for GW397LXUB06

If you know the range repair part you need, you can browse the list of all parts on the GW397LXUB06, or you can search by name or part description. You can also find your part by where it is located on the GW397LXUB06 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for GW397LXUB06 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$50.37

Oven Igniter - Vertical Mount

This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven element is giving off no heat or very little, or is not heating evenly. You may also notice a smell of gas. The ignitor may still be glowing, but could still have gone bad. You will need a 1/4-inch nut-driver and a 5/16 nut-driver. Open the oven door and pull the door off the hinges to completely remove. Pull out the racks. Using your 1/4-inch nut driver, take out the screws at the bottom rear end of the oven, which will allow you to completely remove the bottom. Unscrew the nuts holding the igniter in place. Remove the igniter with the 5/16 nut driver. You should now have access to remove the old igniter.

$24.22

Short Oven Sensor Kit

The temperature sensor on your oven detects the temperature within the oven cavity. If you notice your oven is too hot, not hot enough, or does not heat evenly, the short oven sens...

$3.02

Screw

This screw is sold individually.

$44.96

Door Gasket

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Bef...

$51.52

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware inside of your appliance. Installing the new rack is simple, you slide it into the pre-existing tracks in your oven. It measures approximately 23 inches wide by 16 inches deep. This replacement part is made of metal and it is sold individually.

$3.02

Screw, Igniter

This screw is sold individually.

$66.33

Inner Door Glass Pane

Glass only.

$6.12

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$34.79

Door Hinge - Left or Right Side

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn’t heat up properly

  • Customer: James from Berwick, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 216 of 241 people found this instruction helpful
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read ... read more

F1 code - gas over would not heat.

  • Customer: george from birmingham, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 142 of 152 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was ... read more

Number touch pad would only work on #4 and #1

  • Customer: Ken from Cedar City, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 67 of 80 people found this instruction helpful
First turn off circuit breaker to stove. Slide the stove out about 4 inches from the counter to expose the two phillips head screws, one on the left side and one on the right side of touch panel. Take out screws. Then take out four Phillip head screws on the bottom side of panel, this will set panel loose from stove. Carefully pull up touch pad (switch membr... read more