Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GU1500XTLB3

GU1500XTLB3 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for GU1500XTLB3

If you know the dishwasher repair part you need, you can browse the list of all parts on the GU1500XTLB3, or you can search by name or part description. You can also find your part by where it is located on the GU1500XTLB3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for GU1500XTLB3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for GU1500XTLB3

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$38.60

Heating Element

This heating element is designed to monitor and control the heat of the water that enters the dishwasher. It is located at the bottom of the dishwasher. If your dishwasher is not d...

Order within the next 12 hrs and your part ships today!
$56.56

Door Gasket with Strike - Black

This product contains both the door gasket and the door strike. The function of the door gasket on your dishwasher is to provide a seal between the tub and the door. The door strike serves as a mechanical actuator for door switch operation and provides door tension for a proper seal. If you notice that your refrigerator is leaking, the door will not latch properly, or it is not cleaning dishes properly, you may need to replace the door gasket. This repair is as simple as removing the old gasket from the channel on the edge of the dishwasher tub, and replacing it with the new one. This product is made of black rubber.

Order within the next 12 hrs and your part ships today!
$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

Order within the next 12 hrs and your part ships today!
$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

Order within the next 12 hrs and your part ships today!
$25.95

Chopper Assembly

This chopper assembly, or dishwasher drain food chopper, chops food particles into small pieces to prevent the dishwasher pump from clogging. If your dishwasher is making grinding,...

Order within the next 12 hrs and your part ships today!
$55.07

Detergent and Rinse Aid Dispenser

This part releases the detergent and rinse aid into the dishwasher.

Order within the next 12 hrs and your part ships today!
$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

Order within the next 12 hrs and your part ships today!
$136.44

Circulation Pump and Motor

The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.

Order within the next 12 hrs and your part ships today!
$16.56

Fuse Kit

When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.

Order within the next 12 hrs and your part ships today!
$7.00

Spray Arm Seal

This seal is located between the spray arm and the water feed tube.

Order within the next 12 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 297 of 316 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

Controller board replacement

  • Customer: tony from carrollton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 196 of 217 people found this instruction helpful
Simple task - remove the front door cover to expose the cover for the control panel which is then also removed. Be sure electricity is disconnected from the appliance, then simply remove the old control board (remove the quick-connect wire harness) and slide the replacement board back in. Reconnect wiring harness, replace cover and door panel, then turn-on e... read more

Loud grinding noise from water pump

  • Customer: Steve from Inver Grove Heights, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 181 of 195 people found this instruction helpful
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put th... read more