This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This lid lock striker is sourced directly from the manufacturer for use in top-load washing machines. It is a white, plastic component located on the underside of the washing machine lid. When the lid...
This drive belt is an authentic OEM part that is compatible with various models of washing machine. The drive belt is responsible for allowing the drum to rotate smoothly during the wash and spin cycl...
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
The agitator rotates back and forth to move the clothes inside the tub to clean the load.
$50.35
In Stock
Questions And Answers for GTW460ASJ1WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
March 19, 2020
Temperature of water is always hot, no matter what you select.Its about 4-5 months old. Both the cold and hot water supply valves are both open.
For model number GTW460ASJ1WW
Hi Gary,
Thank you for your question. If you are not getting any cold water, there are some parts that you will need to check to see which one is causing the issue. You will need to check the inlet hoses and screens, the water inlet valve, the lid lock, the selector switch assembly and the electronic control board. For information on how to check these parts, here is a link from our website that you may reference, https://www.partselect.com/Repair/Washer/No-Hot-Cold-Water/. We hope this helps. Thank you and have a great day.
When my washer fills w/water (once it is full) it immediately drains. I have ran thru the binary codes while in service mode, twice now. I have performed all the tests 1-15 and everything works fine. It doesn't throw a single code. But when I get out of service mode, return to normal mode. I select a wash cycle (doesn't matter which cycle I select it does the same in every wash cycle) hit the start button and let the tub fill once the tub is full instead of going into wash mode it begins draining. Please help me. Thank you
For model number GTW460ASJ1WW
Hello Ken, Thank you for the question. This could indicate the Timer is not proceeding through the cycles properly and skipping to the Drain Cycle. The timer for this model is built into the Control Board and the Board may need to be replaced. We hope this helps!
GE top load washer. It is making a noise -squeeking sound during wash cycle. Pulled washer away from wall and there is a spot under the washer that appears to be grease or oil.
For model number GTW460ASJ1WW
Hi James, thank you for reaching out. According to our research on the model, the Drive Belt appears to be faulty and you may need to replace it with part number PS11767488. If you need help placing an order, customer service is available 7 days a week. Glad to be of help!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Turn off hot and cold water supply valves feeding washer. Disconnect both water hoses from washing machine. Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve. Slightly lift the bottom portion of metal plate and slide to release hooks for
... Read moreeasy removal. Pull back and tilt forward plastic control panel to get it out of your way. Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is. Remove two screws from water inlet valve. (one on each side) Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful. Once you have disconnect the sensor you can remove the water inlet valve. If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve. The new valve DOES NOT come with a replacement O-ring so you will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole. Don't forget to install the O-ring or your washer WILL leak! Put everything back together in reverse order. Check hose connections for leaks. Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.