This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This lid lock striker is sourced directly from the manufacturer for use in top-load washing machines. It is a white, plastic component located on the underside of the washing machine lid. When the lid...
This drive belt is an authentic OEM part that is compatible with various models of washing machine. The drive belt is responsible for allowing the drum to rotate smoothly during the wash and spin cycl...
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in y...
This is a water inlet valve; an electrically controlled solenoid valve that opens and closes when necessary, to control the flow of water into your washing machine during the washing cycle. This part ...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
Ask our experts a question about this model and we'll get back to you as soon as possible!
15 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kathleen
January 21, 2020
Can I take the agitator out to clean under it.
For model number GTW330ASK2WW
Hello Kathleen, Thank you for the question. You can remove the Dispenser from the top of the Agitator and you will be able to see a bolt. Once the bolt is removed you can pull up on the Agitator to remove. We hope this helps.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Mike Skowron
February 22, 2020
Have multiple machines not going into high spin tried speed sensor and locks what's next brain??pressure sensor tests fine too
For model number GTW330ASK2WW
Hello Mike,
Thank you for your question. The speed sensor and door switch system are typically the parts you would look at with your symptoms.We would recommend taking a multi meter and checking the electronic parts to see if they are getting proper power to them. While you are doing that, checking your belt is recommended. Once you have taken these steps, you should be able to narrow down the specific part you will need to replace. We hope this helps you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
James
May 28, 2023
Codes 26. Put in all new rods. After done clothes still damp. If put on drain and spin. Run cycle. Then refills before it opens lid. Tub is balanced
Spins with no shake. Where is the balance ring??
Thanks
For model number GTW330ASK2WW
Hi James, thank you for the question. The balance ring is located at the top of the basket assembly. It is not sold separately, you may need to order the basket assembly for it, the part number is PS12343504. We hope this helps!
Washer will drain but will not spin. Would this be a belt or another part?
For model number GTW330ASK2WW
Hello Jason, thank you for your inquiry. Yes, you may have a broken or displaced drive belt, part number PS11767488. A slipped belt can be put back into place, but a worn-out one needs to be replaced. We hope this information is useful!
Does this machine have a reset after spinning an unbalanced load
For model number GTW330ASK2WW
Hi Keith, thank you for the question. If the washer detects an out-of-balance condition, it will try to correct it during the spin cycle. In some cases, the washer may not be able to balance the load and spin up to full speed. To help keep the washer from shaking, we would suggest making sure it has been leveled properly. We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.