This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
$18.58
In Stock
Order within the next 6 hrs and your part ships today!
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
$14.29
In Stock
Order within the next 6 hrs and your part ships today!
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
$36.13
In Stock
Order within the next 6 hrs and your part ships today!
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
$11.56
In Stock
Order within the next 6 hrs and your part ships today!
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
$88.17
In Stock
Order within the next 6 hrs and your part ships today!
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
$9.25
In Stock
Order within the next 6 hrs and your part ships today!
This is a lint filter screen that is used for many dryers. It has a metal screen with a white plastic frame, and is approximately 13 inches wide. This part is sold individually. The lint filter traps ...
$70.13
In Stock
Order within the next 6 hrs and your part ships today!
This is a genuine OEM replacement timer (60Hz) for your dryer. To complete this repair you will need a #2 Phillips screwdriver. To access the timer, you will need to remove the top of the back panel. ...
$111.92
In Stock
Order within the next 6 hrs and your part ships today!
This knob accepts a D shaped shaft. Sold individually. This control knob is for dryers.
Control knob lets you control cycle settings.
Remove the knob by pulling it straight off its post.
$29.09
In Stock
Order within the next 6 hrs and your part ships today!
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
$34.79
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for GTDP200EF1WS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wayne
August 17, 2021
Only runs for a few seconds then shuts off, but has heat
For model number GTDP200EF1WS
Hello Wayne, thank you for your question. There are a few parts that could make your dryer turn off too soon, and all can be tested with a multimeter. Make sure you cut power to your appliance before doing any repairs or tests. First you should test your cycling thermostat, part number: PS267926 with a multimeter. A good thermostat will read 0. If the readout says infinity instead, your thermostat will need to be replaced. Second you should test the High Limit Thermostat, part number: PS267900 Place the thermostat on an electric griddle or skillet and set the heat to the temperature matching the high limit designation on your thermostat. Touch one of the probes to the left gold inner terminal and the other probe to the right inner terminal. Monitor the readout. The instrument will show between 1,000 and 1,200 ohms of resistance as it heats. If the thermostat switches off by showing zero ohms of resistance within 5 percent of the designated temperature, the thermostat is working properly; however, if the thermostat does not switch off, or switches off prematurely, the thermostat is faulty and must be replaced. The third thing it could be is the Dryer timer, part number: PS8690648 Clip or touch one probe to the terminal from which you removed the wire. Touch the other probe to one of the other terminals. You should get a reading of zero. If you get a high reading, then the timer motor is bad and it's time to replace it. These are the most common parts that cause this issue in your appliance. So, it is suggested you check them first. I hope that helps. Good luck with your repair.
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and
... Read more drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
2 screws removed to remove top. 4 screws removed from inside to remove front panel w/ door. 4 screws removed from top of control panel, loosed and popped top right off. Flathead screwdriver to pop off old plastic panel. Removed old wire chas
... Read moree (plastic, approx 3” long). Removed built-up lint, wiped down area for new duct. Snapped new duct on. Dryer works like new!! Took about 35 minutes, most of time spent cleaning up inside of dryer from lint due to broken duct.
One problem was that salesperson sold me on a new felt strip to go with new duct. That felt comes already installed on the new duct so I did not need it. Cost me a few extra dollars I did not need to spend.
Other than that, easy ordering, fast shipment, and parts are as close to original as possible.
