GT2123NEHW Maytag Refrigerator - Instructions

filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : )

To make instalation much easier, I removed the door and layed it on a table. I then remobved about 45 screws,removed the inner door section, removed the seal and installed new seal in reverse order being careful not to over tighten the screws. Having the door lying on the table made it much easier to place the gasket in place and make any minor adjustments. I then replaced the door and everything workes just fine.

Cooling coils froze up. Removed back panel in freezer section. After thawing coils, manually advanced defrost timer to check if fan stopped and defrost (heat) strips energized. Fan did stop, but heating strips did not energize to thaw coils. Used electrical meter to determine circuit was open at defrost thermostat. Ordered replacement and installed in about 20 minutes. No issues so far.

Replacing the door seal only involved unscrewing about 50 screws, attaching the new seal, & screwing all 50 screws back in. I'm glad I have a good electric screwdriver. The hard, if not impossible part, is trying to get the door to seal properly again. At first the door wouldn't close all the way, so after 2 hours of tinkering, it will close now, but the top left corner of the magnetic gasket will not seal no matter what.

I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!

The repair goes much easier if the door is removed. The door is bulky and that's the difficult part. Once its on the table, unscrew to get old one off, put new one in place and re screw. (there are many screws) Then bulky door needs to be placed back onto the refrigerator. Again difficult positioning, weight, bulky. The door comes off and goes on very easily (2 mins to get off, 10 to put back on). Just 3 lower screws. This job could have taken less than an hour if I had started with a removed door.

The first order of business was to find a supplier for the gasket and to make sure that the right one was ordered. This was done with out a hitch @ Part Select and at a cost less than the retail stores. The right Gasket was ordered thru Parts Select

Only difficulty was to start the install of the replacment .
Need to start at the hinged corner of the door Top & Bottom for a good fit and less hassel.

Thank you Part Select for the service.

Alan E. Bischof
Houston Texas

Once I identified the problem, Partselect's web page made it easy to find a replacement part. The Housing Control unit was easy to remove as it had one screw in the middle, by the temprature control section, and two screws to either end. The center screw required a philips head, but the end once did not need to be removed. The unit could simply be slid out and the wiring is easy to disconnect. Then it was simply a process of inserting the components from the damaged Housing Control unit, to the new one. If you treat it like a "puzzle" you'll get the results you want with out the aggrevation that it could turn into.

It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.

The gasket is sandwiched between the main door and the shelf assembly.

What holds them together is 42 1/4in hex head self tapping screws that run along the edge (each one is finger tight).

I would highly recommend a power drill with a 1/4 hex socket to remove the screws. It makes things much faster. Be careful when screwing the screws back in with the power drill(you only want them finger tight). If the screws are too tight,the gasket will bulge out in places.

At first the seal may feel weak. Keep the door closed for a couple of hours and the seal should improve.

Ordered new shelf on a Tuesday night. Part shipped out on Wednesday, received and installed on Friday. It doesn't get any better than that!

No need to repeat the other directions, everyone is spot on with exactly what to do, the ONLY thing I want to add is that prior to putting the new gasket on, throw it into the dryer for a few minutes to make it more pliable..... My problem was that it didn't seat very well, be patient, after 2 days and keeping pressure on it over night, it was a perfect fit !

Having 2 people makes the job a snap. On our model the freezer door had to be partially removed so the other door can be lifted off, then slightly tighten freezer door in place. Lay door flat and remove the 36 screws & gasket making sure the new gasket slots are tucked under to match up with screw holes. We started all the screws & came back and tightened firmly. Loosen the freezer door and set the bottom door back in place, make sure doors clear each other and tighten down. Finished! I took the advice of another post and put gasket in clothes dryer for about 5 minutes,helps a bunch. Start to finish,30 minutes. Taking food out of door & replacing.

I took the freezer door off. Gasket screws ran on the four side of the door. I unscrewed the top and three sides but the bottom screws were completely rusted and stuck. As the refrigerator was almost 19 years old which is the predicted lifespan I decided to just buy a new refrigerator. I was able to adjust the old gasket and got the freezer working normally but decided to go ahead with the replacement.

Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.