Models > GT19Y7W

GT19Y7W Maytag Refrigerator - Overview

Get Parts and Repair Help for GT19Y7W

If you know the refrigerator repair part you need, you can browse the list of all parts on the GT19Y7W, or you can search by name or part description. You can also find your part by where it is located on the GT19Y7W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for GT19Y7W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the GT19Y7W [Viewing 1 of 1]

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

$35.23

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

SCREW

Sold individually.

$2.70

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$2.70

Screw

This screw is sold individually.

$45.64

Relay and Overload

Also knows as a start device combinaton relay and overload.

$26.48

Defrost Thermostat - With Wire and Clip

This refrigerator defrost thermostat will cut out at 80 degrees Fahrenheit and kick back when the temperature drops to 15 degrees Fahrenheit.

$2.70

Speed Nut

$40.79

RELAY-STRT

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 88 of 91 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 17 of 20 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more

Fridge. freezing up

  • Customer: Robert from Salado TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 21 of 33 people found this instruction helpful
First I thank parts select for such fast shipment and correct parts.
The main problem was defrosting the coils between the freezer and fridge. The cover plate over the coils could not be removed untill some of the Ice melted.Removed freezer door, and screws each side of outer frige cover to enable cover plate to slide out.(Outer walls have to be pried o... read more