GSSR4170H0WW General Electric Washer - Instructions

took off front control panel, searched the internet for reasons for my problem, replaced the pressure switch, did not fox my problem, replaced the intake valve which fixed the problem.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

Folks,

Thanks to your great web site and help video I got this fixed in less than a minute. Literally less time than it took me to watch your helpful video. Don't know how to thank you - keep up the good work!

unpluged the machine.undo the hoses off the machine took the back plate off to were I could access the triple water inlet took off the two wiring adators,and the hose that was on the triple water inlet then the two phillipshead screws. throw the bad one in the trash.and then put everything back together

The "service kit belt tool" was difficult to install, but I oonsider it a necessity. We tried installing the belt without the tool, and the belt kept snapping off the motor drive pulley. Using a cable tie to hold the belt to the drum pulley did not work. I used a length of heavy duty duct tape instead, and that worked OK. Unfortunately, the whining noise is still present with the new belt, so a GE service technician visit has been scheduled. Our belt replacement effort has not been totally wasted, unless the washer can't be repaired economically, since the old belt was fraying.

Took all apart.. front off,top off, took basket top off..took the basket assembley out by unhooking the four shocks. Took a picture of all wireing and fittings. Then came the most difficult. The main nut that holds the basket to the main shaft. If you do not have one of the wrenches made for that nut good luck. Between all the gunk and rusty parts around it. It would not budge. I used a pipe wrench and a 3# hammer and it wouldnt budge. It is a oppisite drive nut so it comes off in reverse as a regular one. I ordered the wrench on line to use on the new one i orderd. Had to because the nut was getting chewed up. So waiting to order the parts i needed i ground down the nut with my angle grinder.. worked well. Knowing i had to replace the main drive and bearing it wasnt that bad. Got the nut off... pulled the basket out and then the shot seal. Really looked tore up. So because of the seal leaking, the water drips down onto the main drive and thats what ruined it. Cleaned everything up really nice.. went to put the new seal in and noticed it didnt fit as tight as it should.. so i put some silicone around it and installed everything back together. Still thinking of the seal still i went ahead and finished it all and guess what. It leaked.. the seal in my opinion needs to fit over top of the plastic main bucket not just inside of it. After researching the same problem some guys said they filled the bearing seat with silicone and it helped. Others say the plastic tub needs replaced because the bearing seat is wore out.. the tub is like $70.00. The seal is $8.00. So, what to do? Buy another tub and seal and hope the seal fits in tight, or gob alot of silicone on the seal and older tank and see.. the washer new was like $600.00. Been dicontinued now. The main shaft assembley was $160.00... seal$8.00.. the tool for $15.00...misc stuff still comes out to $200.00 . Now to buy a new tub? Is it worth it or not.. we'll see

Tub seal was found completely broken. Replaced it.
Then replaced tub bearing, tub bearing washer, shaft & mode shifter assembly and 6-rib drive belt.
Reassembled and tried, more quieter and like new machine.

Loosening tub nut was a challenge as it was bit corroded, use of WD40 was a great help.
Knowledge from you tube was a great help.

Just slipped it on. No problems, No Tools.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Removed the bolt holding the agitator coupler on, replaced it and the bolt then slid the agitator on the coupler and the fabric softener dispenser on top of that.... so easy!!

Remove control knob and replace it with new part.

One retaining clip to remove and replace part.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen