Models > GSL25JFPABS > Instructions

GSL25JFPABS General Electric Refrigerator - Instructions

All installation instructions for GSL25JFPABS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GSL25JFPABS
1,171-1,185 of 1,598
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No water dispensing in door

  • Customer: Stanford from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I utilized your other tips on your website and they worked very well. Only problem, I ordered a part that I did not need, but I returned the part to you and your return policy worked well. Thank you for your support.

water dispenser stopped working.

  • Customer: James from Hermitage TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed rear cover at the bottom. Turn off water supply. Disconnect dual water inlet control and replicated it with the new one. reinstalled rear cover and turned the water supply. back on. That's it.h

No water to ice maker and water

  • Customer: Stephanie from Tishomingo OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch to step by step video instructions on your site. Great service! Part arrived the following day after order!

Leak

  • Customer: Frank from Lutz FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Had a water leak on that valve for probably the last 7 or 8 years. Only noticed it when I had a huge water issue with a leaky faucet. Repaired that, went to repair the Sheetrock behind refrigerator and saw water in the tray under frige. Wiggle hose and realized that the reason the water on the front door would only trickle out was because the leak on that valve was also affecting the pressure on the front door. Unreal!! The website and video made it incredibly simple to replace, u guys rock, for real!!!

Water in Door would not cut off. Solinoid on flap ice shute would not close. Corroded and inoperable.

  • Customer: Kenneth from Blairsville GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video instructions were outstanding in showing how this repair was to be completed. Follow these instructions and Job was very easy. Replaced ice shute flapper and arm, soloinoid and Micro switch for water flow control. Reassemble by reversing procedure. Follow video instructions on how to replace water control valve in back of fridge. Test water flow at bottom front of fridge and defrost flow tube in door if necessary. I used tupperware container with hot water on top of ice shute shelf in fridge door. A couple of times changing and water was flowing. Great site and detailed video instructions for an effective and cost saving self repair. I saved several service trips and service calls and labor costs of a service tect. Parts costs were also a lot cheaper than service tech would have charged. Thanks PartSelect.

Water running in freezer compartment

  • Customer: Larry from Raymond NE
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Original equipment valve ran from 2003 to 2010 until a mouse got on top of valve and did a number. Valve purchased in 2010 (installed to solve the same water flow problem occuring in 2012) was installed. I constructed a small tin shield over the valve unit in 2010 to protect the top of the valve from future possible damage. Two years later, the valve failed again - water flowing in freezer. (These Chineese replacement parts should really last longer than two years - I feel they insure future sales by making them poorly) - Both times, the outlet tube above the ice maker was completely iced up and a good deal of time was spent with a hair dryer to melt this ice. (This ice problem can be observed by looking across top of freezer compartment to observe the water outlet area. Turn off water supply and unplug fridge. Four screws were removed to get to the ice maker and then two top screws were removed to pull out ice maker unit (I left hose attached and unit hanging with some support) When installing the double valve, I blew on the loose water tube going up to the ice maker to be sure it was ice free. Taking the old double valve unit out was simple, just remember to press in on the plastic structure around the plastic tubes before pulling out the water tubes. Reattach electrical connections. Press the plastic tubes in as far as they will go for a water tight connection. Reinstall water supply hose and tighten nut. With ice melted, reinstall ice maker with two screws and the front ice maker panel with four screws. Plug in the fridge, turn on the water and you should have ice again as soon as the freezer gets down to 15 degrees.

Water button on door failed to work

  • Customer: Diane from flagler beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed back panel and checked water lines which were empty. Followed booklet instructions for problem solving first. Water Valve appeared to be hot. Ordered new part which came in record time. Removed water lines and connected new part which was fairly easy. Replaced filter and still no water coming up but only going down to new part. Opened freezer door thinking reservoir frozen and left door open for 20 minutes which caused reservoir to defrost itself. Button now works.

Water leak from the valve.

  • Customer: Sudheer from Plano TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I just followed the instructions from the video attached to this order. Thanks to Parts Select for sending me the part on time and attaching a video showing installation.

No water coming out of the water despensorf

  • Customer: Gerold from Edmonds WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
very easy not difficult

No water from in door dispensor

  • Customer: Billy from Noel MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the part, fast shipping, watched the video, great video, made the repair, customer happy. What a great experience for all of us. Bill

water leak behind refrigerator

  • Customer: douglas from englewood CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Identified very small stream of water shooting out of center of blue plastic housing where the icemaker/water dispenser hose connects to external water source. A flashlight up close made it possible to see the water stream, after removing the steel cover from the lower back of the refrigerator. You remove the black and white hoses by PRESSING in on the white plastic rings. I unplugged power before removing/reconnecting the 2 electrical connections with needle nose pliers. Replacing this thing stopped the leak, but I also had to change the circuit board to solve the icemaker water dispenser issues. I also replaced the vampire tap on the house supply line with a shut off valve so I could do this repair without shutting off the house water supply. I did have to shut it down to install the valve, but now I can shut off the refrigerator water supply when needed to replace the filter.

Water valve leak

  • Customer: Samantha from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I followed the video instructions

double outlet water valve was leaking

  • Customer: Ramon from La Quinta CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
after ordering part I went to partselect and watched video. Than I removed old valve and replaced it in the reverse order. it only took 15 min. to do the job.I highly recommend the use of partselect for repairs.

leak under refrigerator

  • Customer: Leroy from Palm Desert CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I followed the video sent with the repair kit

Ice maker not functioning and Tube assembly was to short

  • Customer: Samuel from Madison AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The video explained everything step by step. Repair was easy and only took less than 10 minutes. The ice maker didn't work until several hours later. I would imagine it would have to freeze the ice first. By the next morning it was making ice. Thank you for sharing the video.
All Instructions for the GSL25JFPABS
1,171-1,185 of 1,598