GSH25JSTASS General Electric Refrigerator - Instructions

Used putty knife to pry off frame from around dispensing unit. Pulled circuit board forward and unscrewed dispensing mechanism. located micro switch and replaced. Reinstalled dispensing unit, circuit board and frame.

it was every easy i follow the instructions and took of the old and put on the new and now my frig look very good inside like new. thanks partselect ms miles

Followed the video on line step by step and it went very well with no problems disassembling or installing the new part.

Replaced board, easy to diagnose and repair.

It was simple just applied some common sense to trouble shoot and remove the motor from the housing in the back of the freezer. Then reverse the order when replacing. The part arrived in 1.5 days from when I placed the order. Joshua

Upon inspection I discovered the Dispenser Crusher Cover was broken which allowed the ice to bypass the normal route. I went to your website and found a customer's testimony regarding a similar problem. It was titled "Noticed pieces of broken plastic in my ice cubes." I ordered a new Dispenser Crusher Cover, ran a copy of the testimony and waited for the part which came in within three days. I followed the instructions in the testimony and the problem was corrected in less than 30 minutes.

entered the part number in You Tube! A nice fella stepped through the process... It was EASY

Very Easy, follow direction I the video.

Lift up and remove dispenser grill tray-Install new tray. Unscrew water filter upper right side of fresh food section. Screw in bypass cap.

Just as described in earlier reviews, this was the filter housing unit and not the double water valve. To determine which part is failing bypass the water filter unit by disconnecting both water lines and connecting the fresh water line directly to the water valve. If this solves the problem, then you know for sure the filter housing is the problem. The filter housing has a very small tab that pushes open a rubber flap valve when a filter is installed. This allow you to remove the filter without turning off the water supply. Apparently only a very small amount of wear prevents the flap valve from opening fully and allowing water to flow. A small amount of water flow may be evident with the water dispenser but the ice maker will keep working until flow is completely interrupted. Easy fix.

This has been a problem for some time and had I known how simple it was to repair, I would have done it a long time ago. I followed the online instruction provided and had it done in under 15 minutes! I removed the upper drawer and shelf, the middle drawer and glass shelf, unscrewed the 2 screws holding the broken slide rail to the side of the refrigerator, applied the new slide rail in place of the old, replaced the glass shelves and drawers and that was it! Works like a charm!

I saw the video on the Part select website how to replace the Auger and Auger Nut. I ordered the parts and proceeded with the installation which was relatively simple. The video was extremely helpful. I don't think I would have attempted the repair without it. Also Parts Select reps were extremely professional and made sure the parts were applicable to my model before shipping.

I called angies list to get a name of a repair person . We were having very hot weather and I did not want my freezer food to spoil. The cost was not bad for the look see $127.00 plus parts and labor added on to this. I decided to look on the internet and found your services and the video on how to replace the part that might be bad. I bought a new thermostat and also a sensor and added the control board as the refrigerator is 13 years old. I spent a total of $206.00 and did the work myself so no labor cost. I was so happy as a new refrigerator like this one would be $3100.00 plus tax. Thank You R. Polglase

Watched the video. Extremely helpful. Replaced valve and now the water dispenser shuts off, like brand new. The valve must have had some calcification and would not completely close.

Pulled the Ice Maker tray out, emptied the ice and turned the ice maker off. Then I took the inspection cover off, which was simple but I was trying to remove the Ice Crusher Assembly, I thought I might break the tray assembly if I forced it. I remembered seeing a link for a video link. Took time to watch it, just a few minutes, it made mention that you needed to let the tray warm up or it could crack when you pry the ice crusher assembly out. Once I saw how they removed it, it was a piece of cake. Guys watch the video and it will be a simple fix.