GSD6660G00SS General Electric Dishwasher - Instructions

installed new silverware basket

Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process

Pulled out the lower tray, snapped off the wheel and Stud Roller, put the wheels on the new Stud Roller, and re-install. A monkey could do this one. It works fine now but will most likely go bad again. I see this as a temporary fix. I'm working on something more robust. My wife says just replace them every couple of years because they are so inexpensive and easy to replace. I guess she has a point, but making a bullet proof alternative seems like a lot more fun and gives me one more excuse to be in my shop.

opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake

I just ordered another one of the wheel rack and it was that easy. No tool required.

Remove the door panel screws on the inside door frame. You only need to remove as many as needed to remove the larger bottom panel. The other screws will remove the upper button panel and this is not necassary. Unplug the Detergent Dispenser (it may take some force, and unscrew the dispencer. Replace with the new one, screw back in place, and reattatch the plug. Now replace the door panel and screw it back in place. This is all very simple. The only problem I encountered was that the only dispenser had built up so much detergent residue around its base, that it had distorted the plastic around it. This caused the new dispense to not sit flush all the way around, and the dishwasher leaked into the door on its first cycle. Simply filling the gap with 100% silicon caulk has fixed the problem. Washes like new.

Replaced 2 wheels, one of which was lost, the other of which had gotten partially melted by the heating coil after it had fallen off. Replaced all 8 of the axles. The problem was with the old method of attaching the axles to the dishwasher. They were attached on the side, so they could fall off in one direction. The new axles flank the post and can not come off in a sideways direction. Lower rack now rolls in and out securely. No more having the rack suddenly fall when a wheel comes off. Don't hesitate to effect this repair yourself.

Pull rack out put wheel on put rack back

I firts turned off power to the diswasher through the circuit breaker panel. I removed the black tray at the bottom front of the dishwasher, removed the two screws attaching the water inlet valve, detached inlet and outlet water hoses as well as the eletric connector. I removed fitting from the old valve and installed in the new valve using some teflon tape. Installation is the reverse of the removal.

Removed the holding screws around the edges; removed and replaced the soap container; reconnected the electrical leads, and done... Very simple fix. But it does get a little tricky since the door is spring loaded. NOTE: THERE ARE SCREWS AT THE BOTTOM THAT IS NOT OBVIOUS.

Just took old ones off and replaced with new one. Snapped right in. Replacements were heavier and better made look like they will last much longer.

Ordered a replacement hub and wheel - snapped together in just about 1 minute.

Hard to push part through hole in wheel. used pliers to help.However replacement is better quality than original wheel atachment.

I was offered a free dishwasher for the taking. The soap dispenser latch was broken. I ordered the part, it arrived two days later by standard delivery. The door cover has to be opened and seperated. The difficulty is that the door will not stay down or up without assistance. Once open, the dispenser is replaced by removing 6 screws from within the door compartment (between the door front cover and inside door wall. Two electrical leads must be removed and reconected to the new part. Removing them is problematic, since one connecter partially chipped off using pliers to gain a grip. After inserting the new part the 6 screws are installed from behind the part and the leads reconnected. There are two ribbon connectors for the control panel and display. They did not come loose so I left them connected, which made it awkward to manipulate the various parts with the door split open. Putting the ribbons in proper place was easy if careful. Securing the outside and inside halves of the door completes the repair. I found instructions on google. This was tricky but easy, as the door parts were often trying to move out of an accessible position for working. Otherwise it was one of the easiest things I have done. It would be easier with two people, and I had only one good arem to work with due to shoulder surgery, but it was successful. The dishwasher works fine, and the price was right at $45.00 in parts plus shipping for a top of the line model.

Put axles on wheelsd and attached to the bottom dish drain. Received the new parts in a most spectacular time frame. Thank you.