Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GS6SHEXNS00 > Instructions

GS6SHEXNS00 Whirlpool Refrigerator - Instructions

All installation instructions for GS6SHEXNS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GS6SHEXNS00
1,096-1,110 of 1,433
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

ice maker not making ice

  • Customer: Travis from La Crescent, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My ice maker stopped producing ice after our refridgerator was accidently turned off for 4 days. Note: the on off switch in the front does turn the unit off even though the light stays on, why we need easy access to turn off the fridge is beyond me. Regardless, I spent way more time researching the problem then doing the repair. There is 2 things that could be wrong: 1 was the infra red light located on either side of the freezer, called the transmitter/reciever. 2 was the side of the ice maker control panel. Either one or if I had to replace both it would of been less then the cost of a repair man to come to my home. Prices here a good. I started with learning the diagnostic of the ice make which is learned by watching the red light flash. That informed me that it was working ok. Reference: if you hold back the hinged plate and pretend the door is shut the light should flash, flash, pause. This means its working. I went with the other route of the control module on the ice maker. This part came fast like 2 days. I watched the video on the parts web page and it was simple to do. You do have to wait until the temp goes down below 15 degrees in order for the ice maker to kick in. I won't buy another kenmore for I have had plenty of trouble with this one and its bearly 6 years old. I'm Definetly a fan of this website. Good luck DIY ers!

no ice cubes

  • Customer: Linda from Pawhuska, OK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your youtube repairman twice. the video was very good concerning how to do the replacement.Thank you very much this is a lifesaver for people like myself that can not afford a repair person to fix broken items at the house.

ice maker quit making ice

  • Customer: Joseph from Lakewood, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked on line to see repair instruction videos on my refrigerator ice maker. When I saw how easy I went to PartSelect and order the part (control and motor assembly). I received the part in two days with the cheapest shipping option. My 33 yr old son was visiting when the delivery was made. After we opened the box, he went to the basement for tools and the rest is history. 10 minutes work and ice a couple of hours later! No problems since.

Ice maker just quit working!

  • Customer: Keith from Sanford, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.

Ice maker stopped working

  • Customer: Stephen from Lynnwood, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching a YouTube video I was able to determine that my ice sensor was working properly. I was getting water through the door dispenser so I decided to pull the icemaker. First I removed the 2 hex head screws holding the ice door which gave me access to the icemaker. I removed the hex head screw holding the electrical plug cover on the bottom right side and removed it. I then pushed up on a plastic tab on the bottom left side of the ice maker and slid the icemaker out so I could access the electrical connection. After unplugging the electrical harness(plug/socket) I completely removed the icemaker from the freezer. The white square end cover easily pulled off the icemaker exposing the control and motor assembly. After removing the 3 screws holding the assembly on I pulled the assembly off the end of the icemaker. Installation was as simple as assembling the parts in reverse order making sure that the ice delivery male shaft "flat" mated with the "flat" on the motor drive female socket. After reassembly I went for a bike ride and when I returned about 3 hrs. later I was happy to see my icemaker was making ice again. This is actually easier than it sounds if you have any mechanical apptitude whatsoever.

Ice maker stop making ice cubes.

  • Customer: Ken from Nampa, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I saw the question listed on your website with your recommended part to repair. Instead of ordering a whole new ice maker I took the chance and ordered the recommended part for repair. I saw the video and when the part came it was really easy to replace. I only wish I had found your website earlier and not gone without ice for as long as I did. Thanks.

Ice maker made ice but would not dump it into ice container

  • Customer: Danny from Martin, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the motor and everything is working great!

Ice maker stopped making ice - repair not successful

  • Customer: David from Lewisville, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the flapper door. I removed the screw to remove the wire connection. The ice maker slides out easily. I disconneted the power wires. Removed the motor cover. Removed the 3 phillips screws. Replaced everything in reverse order. I unplugged the unit to reset the LED panels. The ice maker is still not making ice.

Wasn't making ice.

  • Customer: Carol from Brooklyn, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered both icemaker motor assembly and the emitter and receiver (sensors)as I was uncertain as to which was the culprit. We couldn't unplug the frige as it is heavy, so we shut the circuit breaker until we were done with the repair. The icemaker motor was a bit clumsy to remove. My refrigerator was entirely different than the one on the video I viewed, as I have a side by side and the video was of an entirely different model. The video's icemaker was not as clumsy to work with. My husband was a little apprehensive so I rode shot gun and assisted and he did great. He did change the motor first and probably should have waited to see if it worked. He didn't wait, and went ahead and changed the sensors....that was a breeze. We waited about 2 hours and lo and behold once the freezer went down to 14 degrees, the icemaker began it's magic and we had a full supply of ice within 24 hours. So, I saved quite a bit of cash by purchasing the parts I needed at Parts Select and eliminated the repairman's expensive fee. Very happy with end results.

Icemaker stoped making ice.

  • Customer: Henry from Missouri City, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.

ice maker stopped making ice.

  • Customer: Rliot from Dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removedicemaker and unscrewed 3 screws hill ding motor assembly and control module to ice maker . nstalled new part and attached it with the 3screws. reinstalled ice maker and ice making cycle began almost immediately.

Ice maker quit making ice

  • Customer: Charles from Mesa, AZ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
A local appliance parts distributor suggested that I go on line to get help figuring out the problem. The motor assembly was 51% probability. I ordered the part and followed the instructions given at the time of purchase. In a very short time ice was dropping.

plastic gear in ice maker was broken

  • Customer: Chieu from Suwanee, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Just watch video from part select and following the instruction to replace the control and motor assembly.

Stopped making ice

  • Customer: Erin from Indianola, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have a side-by-side fridge/freezer, so taking out the icemaker is a bit more tricky than the video shows. I just unscrewed a nut in the back right of the mechanism (this nut is holding the icemaker in place as well as the plug cover). Once that was off it slid out pretty easy. Because the freezer is so narrow, it's a bit difficult to get it back in, but all told the repair took me about 20 minutes. Replacing this part fixed the icemaker immediately and we're so glad to have our on demand ice back! Ladies, don't be afraid of a little appliance repair!
All Instructions for the GS6SHEXNS00
1,096-1,110 of 1,433