GS6SHEXNL00 Whirlpool Refrigerator - Instructions

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

My first try was to replace the water inlet valve. New valve was a good bit different than the original but not too hard to figure out. The main water inlet is on the inside rather than the outside. Flex hose and a stick in connector were included and I was able to work through that. But, when I turned it on the water still over flowed. The only thing left was the Ice maker. I ordered a new one. It came broken into several pieces. I ordered another, it arrived overnight with expediated shipping. install took maybe 15 minutes. problem solved. The company refunded me the full charge for the damaged ice maker and most of the charge for expediated shipping on the replacement. I'm happy and my wifes very happy.

I watched the video on line and fixed as per the easy demonstration. Sad something 4 years old breaks.

The unit came out easily but the wire harness connector just didn't want to disconnect. The ice cold plastic was very difficult to work with and I had to use a screw-driver edge to pry it up and apart.

Unplugged refrigerator, took panels off each side of ice maker, unplugged bad components and replaced with new ones. Returned panels, plugged refrigerator back up. The ice maker began making ice almost immediately.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Watch replacement video then went from there. It was a simple replacement. Icemaker working and wife is happy:)

I took the ice maker right out

Defrosted freezer only. . . . Unplugged fridge. Took hairdryer and made sure all access water was turned off to fridge; then kept heat on hose lines behind metal panel for 10 minutes. Saved myself 382. 00 Repair bill and within an hour had the ice machine banging out the ice. When going on vacation, make sure ice maker is turned off and even if it doesn't work when you get back, defrost freezer before calling help! Saves sooo much money and the new fridge I was told I'd have to purchase if it happened again. Don't think so!!!!!!

followed thr video. very easy

At first I just ordered a new motor and followed the instructions on the video . The new motor started working overtime but no water was being delivered to the tray . Ordered a new tray and re-installed. Working fine now. At first the ice was sticking, but that seems to have stopped now. It may be better to pull the ice maker out and check to see if there is damage to the tray before ordering. That way it could save the time of not doing things twice.

Replaced control and motor on the basis that most respondents found this unit to be at fault when the icemaker failed. Unfortunately, this wasn't the problem. Sudsequently, I replaced the electrionic boards which did fix the system. It would have been helpful (and less expensive) if the patrsselect website provided more help with problem diagnosis. Otherwise, the website is great!

Remove ice unit to take out ice. Remove both boards and replace.Had to unplug refig to thaw out water line because it froze when unit would not make ice.

It was a very simple repair. The only frustration is that all I needed was a small plastic part on the motor assembly but had to buy the entire assembly. Glad that I found the assembly much cheaper on your site, but wish I could have just bought the small plastic part.