Models > GS6SHEXNL00 > Instructions

GS6SHEXNL00 Whirlpool Refrigerator - Instructions

All installation instructions for GS6SHEXNL00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GS6SHEXNL00
61-75 of 1,419
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replacing slide track to meat drawer shelf

  • Customer: Cynthia from Tucson AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 19 of 21 people found this instruction helpful
The slides fit into the slots of the self metal, but couldn't be pushed forward to lock into place! At first I tried to put the slider in by hand, but it wouldn't snap in place no matter how hard I tried. A friend also tried to get the slider into the slots and push forward to lock in place in the metal part of the shelf. No go! It took a while, but I figured if I used a hammer to tap the slider into place that might work. It did. It would have been helpful to have some instructions on inserting the slider, such as "use a hammer tap the slider so it locks the slider into place". You just can't do it by hand! Other than that, it went really well and replacement then only took 1 minute. . .instead of the 30 minutes it took to try to lock the sliders.

Compressor "grounded" and quit running

  • Customer: Mike from Baytown TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 39 of 82 people found this instruction helpful
Replaced the compressor with the new one I purchased from you. Installed new parts and recharged unit. The refrigerator / freezer is working better than new. Thanks for the great deal on the compressor. It was here in 3 days. All the parts fit exactly and had no difficulty in the installation or startup. The directions for the wiring were a great help also. Thanks again.

The filter needed to be replaced

  • Customer: Eva from Arlington TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 20 of 26 people found this instruction helpful
Removed the old filter (it screws out) an put the new one in!

water filter needed changed

  • Customer: Gerald from Findlay OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 23 people found this instruction helpful
Turned the lock knob on the filter and removed. put
lock knob on new filter and installed.

Very user friendly website, would highly recommend to anyone.

Fridge was not cold and freezer was way to cold and defroster was not running...

  • Customer: Michael from Riverview FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 20 people found this instruction helpful
I possibly could have done the entire repair with the last part used but who knows...Anyways the fridge was not getting cold and the passage that blows cold air from the freezer was clogging with ice as was the cold air intake spot at the bottom of the freezer coils...this problem behan 3 months ago...I replaced the thermostat first...didnt work...second, a new burner element....also did not work and finally what worked was a new control board at the back of the fridge...also the lights in the fridge went out 3 years ago and now they are back on after the new board was installed...hope this saves someone else some time and frustration.

Refrigerator stop cooling

  • Customer: kelly from glen allen VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 24 people found this instruction helpful
I was about to waste $1000 on buying a Refrigerator. Took 1 mins to search on google "Refrigerator doesn't work". Found a video on youtube, showed a step and step video to solve my problem. Order the part $50 and it took me less then 5 mins to install it. =)

The ice maker stopped producing ice.

  • Customer: Robert E. from Payson UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 17 of 18 people found this instruction helpful
If you remove the bottom vent panel of the refrigerator there are two schematics for the refrigerator. One for the fridge and one for the icemaker. The icemaker has an emitter and a receiver that will tell the icemaker when it is ok to dump ice and add water. The receiver has an LED that blinks different codes. The codes give you an idea where your problem is located. In my case it coded out to be the optics (emitter and receiver). Replacement of the parts involves the removal of three screws on each component and disconnecting a wire harness on each component. Install the new components by following the removal process in reverse. The total cost was $80.00. This was half the price Sears wanted for the parts and about the same price to have a Sears repairman just show up at the house.

tracks for the deli drawer were broken

  • Customer: Terri from Wichita KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 18 people found this instruction helpful
I removed the old tracks and installed the new ones. There were small round protrusions on the new tracks that prevented me from sliding them into the brackets in the refrigerator so, I filed them down with a fingernail file and then they slid right into place.

Icemaker arm was broken

  • Customer: Jason from Austin TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 19 of 24 people found this instruction helpful
The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

ice would not fall from ice maker

  • Customer: Greg from Cary NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 20 of 28 people found this instruction helpful
I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.

Filter Housing Unit Leaking

  • Customer: John from Vernon CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 19 of 25 people found this instruction helpful
It was simply a matter of removing the old filter housing unit by unscrewing 3 screws and unplugging the two water tubes. After re-insterting the water tubing and securing the housing unit "VOILA" good as new..It really was easy..

One finger of the spring steel peice that holds the ice maker and water dispenser levers out broke.

  • Customer: Ron from Newton IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 20 of 28 people found this instruction helpful
I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron

The icemaker stopped filling the ice tray to make ice.

  • Customer: shannon from sierra vista AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 18 of 22 people found this instruction helpful
I checked the fuses and hoses in the back of the refrigerator to make sure water WAS in fact getting to the front of the fridge. Since the water through the front door worked fine, I had to check the water tube running to the ice maker. It was fine and water was waiting to go somewhere! I decided to pull the icemaker out of the fridge to see what I could fine. Once it was out, I took the ICEMAKER CONTROL AND MOTOR ASSEMBLY off (that's the side part with the dial on it). Only 3 screws to take that off, and it was EASY to see what was wrong once I took that off. There was a connection that was obviously bad (looked almost like it had burned out). My thought was that it was obvious what part was bad, what would it hurt for me to try to fix it myself? When I got online to find the part, PartSelect was the only one that I found that had the EXACT part that I needed, and lucky for me, there were multiple pictures of multiple angles of the part so I could compare and make sure I had the right one!! The part with shipping cost less than the cost of a repair tech to even come out and look at the fridge. Then add the cost of the part and labor if I had the repair tech fix it...I probably saved about $250!!!!

Ice maker not working

  • Customer: Lisa from Stuart FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 20 people found this instruction helpful
Well I changed out the optical boards which I thought were the problem and the ice maker is still not making any ice. I can see the ice makers fingers rotating but there is no water entering through the tube. I jumped the water manifold in the back and water comes out but I cant figure out what is not telling it to run water and fill the ice tray. Any ideas would be appreciated I guess i'll replace the ice maker next. Thanks in advance.

Water running out of cold water in freezer door

  • Customer: Jackie from Niota TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 18 of 23 people found this instruction helpful
took back of refrigerator, removed water lines, removed electrical connections. removed 2 screws holding water valve, replaced water valve, replaced electrical connection, replaced water lines. Put back on refrigerator. Tested water on freezer door. Didn't work, had to take refrigerator back off again and check the electrical. I didn't get one of the connection put on securely, Put back on refrigerator, check water on freezer door. It worked. Make sure the electrical connection are connected this will sav you about 10 minutes of repair time
All Instructions for the GS6SHEXNL00
61-75 of 1,419